background image

 

 

10 

 

13. SAFETY PICTOGRAMS AT THE NESCHEN LAMINATOR

 

The pictograms must always be clearly legibly attached to the laminator. 
Damaged pictograms must be replaced.   

Pictograms and their meaning

. Safety pictograms on the laminator indicate risks, as do the 

warnings in this manual.   

 

 

 

 

 

 

 

 

 

 

14. FIRE PROTECTION  

Since  the  laminator  is  not  factory-fitted  with  fire  extinguishers,  the  user  must  ensure  that  fire 
extinguishers are installed in the building.    

 

Never  extinguish  a  burning  or  live  laminator  with  a  water  or  foam  extinguisher.    There  is 
danger of electric shock! 

 

 

Never extinguish burning electrical parts with a water extinguisher!     

 

Recommended types of fire extinguishers: powder, snow and halon.  

 

In the event of fire, follow the instructions for the appropriate workplace. 
 

15. DISPOSAL OF THE MACHINE OR INDIVIDUAL PARTS 

 

For the disposal of the laminator at the end of its service life, the applicable  environmental 

guidelines must be followed and available recycling options must be applied.    

 

Separate plastic parts and recycle.  

 

Separate and sort metal parts and dispose of as scrap metal.   

 

The operator 
must read the 
User 
Instructions 

Before starting any 
repairs, 
adjustments, 
cleaning and 
maintenance of 
the laminator, 
disconnect the 
machine from 
power mains 

 

Close all covers 
correctly before 
operation. 

Do not touch any 
moving parts on the 
laminator. 

Summary of Contents for PHOTOLAM 650












Reviews: