background image

210-0000025 rev04

3. Connect the T1 Line(s).

Plug the T1 cable into the RJ21 connector for the chosen slot on the back of the IP DSLAM. The 
TAM1500-12 will connect with remote T1 modems at distances up to 6,000 feet before 
requiring a T1 repeater. For each port being connected to a remote T1 modem, verify that the T1 
link has been established; the T1 LK LED for that port will show steady illumination to indicate 
the connection has been made. Link up should occur within 20 seconds depending on the 
quality, gauge and distance of the copper cables. Default bandwidth for the TAM1500-12 is 
1,536 kbps.

T1 RJ21 Connector Port Pinout

OVERVIEW

TAM1500-12 Management

Statistical and configuration data for the TAM1500-12 are maintained in an embedded web 
server that resides within the firmware of Net to Net Technologies' Multiplexer Uplink Modules 
(MUMs). This firmware contains Net to Net's Network Management System (NMS) and Simple 
Network Management Protocol (SNMP).

Accessing TAM1500-12 data in a newly installed IP DSLAM

a. Connect your PC to the Ethernet RJ45 MGMT port located on the faceplate of the 

MUM installed in your IP DSLAM. 

b. Verify the connection; solid illumination of the MGMT LNK LED on the MUM 

faceplate indicates the connection has been established. 

c. Launch a web browser such as Microsoft Internet Explorer (v4.0 or higher) or 

Netscape Navigator (v4.0 or higher). 

d. Type the default IP address into the address field at the top of your browser and 

press the Enter key. 

PORT

1

2

3

4

5

6

7

8

9

10 11 12

RX Tip

26 27 28 29 30 31 32 33 34 35 36 37

RX Ring 1

2

3

4

5

6

7

8

9

10 11 12

TX Tip

39 40 41 42 43 44 45 46 47 48 49 50

TX Ring 14 15 16 17 18 19 20 21 22 23 24 25

  

(Pins 13 and 38 are not used)

NOTE

Once the TAM1500-12 has been installed, all settings are software selectable via Net to Net Technologies' Network 
Management System (NMS). For further information regarding TAM1500-12 configuration and management please 
refer to the Circuit Configuration section further on in this manual and/or to the Management User Guide for IP and 
Mini DSLAMs.

Summary of Contents for 12-Port T1 Access Multiplexer TAM1500-12









Reviews: