background image

210-0000025 rev04

Caution: This unit does not contain any user serviceable parts. Repair service and/or warranty 
information may be obtained by contacting Customer Support at Net to Net Technologies, Inc.:

112 Corporate Drive, Suite 1, Portsmouth, NH 03801
(603) 427-0600 / (877) 638-2638, Contact@NetToNet.com / www.nettonet.com

Industry Canada Regulatory Compliance Information for Class A Equipment 

This Class A digital apparatus complies with Canadian ICES-003. 
Cet appareil numérique de la Classe A est conforme à la norme NMB-003 du Canada. 

Industry Canada Regulatory Compliance Information for T1 Equipment 

Notice: The Industry Canada label identifies certified equipment. This certification means that the 
equipment meets telecommunications network protective, operational, and safety requirements as 
prescribed in the appropriate Terminal Equipment Technical Requirements documents. The department 
does not guarantee the equipment will operate to the user's satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the 
facilities of the local telecommunications company. The equipment must also be installed using an 
acceptable method of connection. The customer should be aware that compliance with the above 
conditions may not prevent degradation of service in some situations.

Repairs to certified equipment should be coordinated by a representative designated by the supplier. 
Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the 
telecommunications company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility, 
telephone lines and internal metallic water pipe system, if present, are connected together. This 
precaution may be particularly important in rural areas. Caution: Users should not attempt to make such 
connections themselves, but should contact the appropriate electric inspection authority, or electrician, 
as appropriate.

210-0000025 rev04

© Copyright 2001 Net to Net Technologies, Inc.

™ The Net to Net Logo is a trademark of Net to Net Technologies, Inc. 

Worldwide Headquarters

Net to Net Technologies
112 Corporate Drive, Suite 1
Portsmouth, NH 03801
USA
+1 877-638-2638

http://www.NetToNet.com/

Contact@NetToNet.com 

EMEA Headquarters

Net to Net Technologies

Victoria House 19 Park Way

Newbury Berkshire RG14 1EE

UK

+44 (0) 1635 570950

Summary of Contents for 12-Port T1 Access Multiplexer TAM1500-12









Reviews: