background image

 

AAM8000-12, AAM8000-24 and AAM8000-24B

 

12-Port and 24-Port ADSL Access Multiplexers with Full Rate and G.lite Operational Modes

 

 

 

 

1.0   ADSL ACCESS MULTIPLEXER MODEL TYPES 

The AAM8000-12 and the AAM8000-24 (Annex A) are twelve and twenty-four port ADSL Access 

Multiplexers, with both Full Rate and G.lite operational modes, that support Plain Old Telephone Service 
(POTS) across lower frequencies (up to 4 kHz). 
 
The AAM8000-24B (Annex B) is a 24-port Access Multiplexer, with both Full Rate and G.lite operational 

modes, that supports Integrated Services Digital Network (ISDN) across lower frequencies: up to 80 kHz 
over a Two Binary, One Quaternary (2B1Q) line and up to 100 kHz over a Four Binary, Three Ternary (4B3T)
line. 
 

All three of the above ADSL Access Multiplexer models exceed the International Telecommunications 
Union Telecommunication Standardization Sector (ITU-T) Recommendation G.992.1 minimum 
requirements of 640 kbps upstream and 6,000 kbps downstream. 
 

 
 

2.0   INSTALLATION 

 
 

2.1   Unpack and inspect the AAM8000 

If there is visible damage, do not attempt to connect the device; contact Customer Support at 1-877-

638-2638 (001-603-427-0600 for international customers) or Support@NetToNet.com. 
 

 

2.2   Install the AAM8000 in an IP DSLAM chassis 

 
Net to Net Technologies' IP DSLAM interface modules are hot swappable; installing or removing an 
interface module while the chassis is powered up does not affect the operational status of other 
interface modules within the chassis. The IPD12000 is a fourteen slot chassis; slots 1-12 are 

reserved for interface modules (such as the AAM8000) and slots 13-14 are reserved for MUMs. 
Interface modules may be placed in any order in slots 1-12. The IPD4000 is a five slot chassis; slots 
1-4 are reserved for interface modules and slot 5 is reserved for a MUM. 
 

Interface Module User Guide

C

AUTION

Net to Net Technologies strongly recommends the use of proper electrostatic discharge (ESD) precautions when 
handling this equipment. 

N

OTE

There must be a Multiplexer Uplink Module (MUM) installed in the IP DSLAM chassis in order for interface 
modules to operate. 

210-0000039 rev 07

Summary of Contents for AAM8000











Reviews: