background image

 

2.5   Speed 

All E1 lines consist of 31 channels (timeslots) that continually run at 64 kbps for a collective 
bandwidth of 1,984 kbps. Timeslot configuration dictates how many of the channels for each port 

will actually receive data. Ports configured to operate as fractional E1 lines require contiguous 
timeslots as indicated in the chart below. 
 
 

 

 
 

3.0   ADDITIONAL INFORMATION 

 

3.1   Configuration and Management 

Once the EIM2000 has been installed, all parameter settings are software selectable via Command 
Line Interface (CLI), Simple Network Management Protocol (SNMP) and/or Net to Net's Network 
Management System (NMS) dependent upon the multiplexer uplink module (MUM) model installed 

in your IP DSLAM. Refer to Net to Net's NMS Management User Guide 

http://www.nettonet.com/support/docs/210-0000048

 ) and/or CLI Management User Guide 

http://www.nettonet.com/support/docs/210-0000052

 ) for further instruction regarding IP DSLAM 

management and interface module parameter configuration. 

 

 

3.2   Data Storage 

Upon initial power up of the IP DSLAM, default parameters of the EIM2000 will remain in place 
unless changed via NMS, CLI or SNMP. Once changed, new configurations will automatically be 
recorded in both the Random Access Memory (RAM) of the EIM2000 and the Non-Volatile Random 

Access Memory (NVRAM) of the MUM. While data stored in EIM2000 RAM will be erased if the 
module is removed from the IP DSLAM, or the IP DSLAM loses power, interface module data stored 
within MUM NVRAM will remain intact (even if the chassis loses power) unless deliberately cleared or
reconfigured. 

 

 

3.3   European Regulatory Compliance 

This Class A product complies with European Norm EN55022.  
 
Warning: In a domestic environment this product may cause radio interference in which case the 

user may be required to take adequate measures to correct the situation.  

 

 
 

Single Line T1 Bandwidth (kbps)

 

TIMESLOTS

1 - 31 1 - 28 1 - 24 1 - 20 1 - 16 1 - 12 1 - 8 1 - 4

COLLECTIVE 

SPEED

1,984

1,792

1,536

1,280

1,024

768

512

256

     

Default bandwidth utilizes 
all 31 timeslots for a 
collective speed of 1,984 kbps.
 

210-0000054 rev0

2

 EIM2000 User Guide Page 19 of 20

Summary of Contents for EIM2000





















Reviews: