background image

 

 

NTC-402 

 Telstra Private IP WAN Configuration Guide 

7 of 11 

CG01068   v. 1.0   October 2018 

© NetComm Wireless 2018 

 

I T E M  

D E S C R I P T I O N  

T E L S T R A   S E T T I N G S  

IP Type 

Use the default setting: IPv4 

IPv4 

SIM PIN Code 

Enter the PIN code that you received with the SIM from 
your service provider. 

Enter your SIM card’s 

unique PIN. 

Dial Number 

Accept the default setting. 

N/A 

Authentication 

Set to CHAP (Challenge Handshake Authentication 
Protocol) 

CHAP 

Username 

It is required for your Telstra supplied SIM and is case 
sensitive. 

user2@netcomm.com.au 

Password 

It is required for your Telstra supplied SIM. 

FrameR0ute 

IP Mode 

Set to: Dynamic 

Dynamic 

Prim/Sec DPN 

Not required 

empty 

Roaming 

Accept the default setting of not enabled. 

 Enable 

PDP header/data 
compression 
control 

Accept the default setting: Off 

Off 

Save button 

Click to save and apply the changes you have made. 

Click to save. 

Undo button 

Click to close the section and discard any entries you have 
made. 

N/A 

Table 2 

 Virtual Server Rule Configuration page 

Disable NAT and Network Monitoring 

7

 

While remaining on the  Internet Setup tabbed page scroll down to the 3G/4G Connection Common 
Configuration section: 

 

Figure 4 

 3G/4G Connection Common Configuration section 

Summary of Contents for NTC-402












Reviews: