background image

User’s Manual 

Wireless Serial Server GW5120

 

 

 

Copyright © 2009 Neteon Technologies, Inc. 

All rights reserved.   

 

Note: ARP commands can only be used to set a static IP address on GW5120   

arp –a

 command shows the current mapping IP and MAC addresses. 

arp –s

 “IP address” “MAC address” maps the IP address to specify MAC address. 

 

3.2.2.  Configure IP by Web interface 

Use Web browser such as Microsoft Internet Explorer to configure the network settings of GW5120.   

„

 

Enter 

IP address

 (default IP: 10.0.50.100) of GW5120 on the browser address bar.  Enter 

user name (default: 

admin)

 and no password (leave it blank). 

„

 

Configure IP settings under 

Network 

section. 

„

 

click 

Save 

to save settings, and ”

Restart

” on the followed page to take effect. 

 

Please refer to contents of 

Web Configuration section

 for more details. 

 

.

 

3.2.3.  Configure IP by Telnet utility 

Use Telnet utility such as Microsoft Hyper-terminal to configure the network parameters of GW5120.   

„

 

Run command 

telnet “IP address

” to telnet to GW5120. 

Default IP address is 10.0.50.100

 

and no password

 

(leave it blank). 

„

 

Configure IP settings from 

network settings

 menu. 

„

 Restart

 system to take effect after new settings are saved. 

 

Please refer to 

Telnet Configuration

 section for more details. 

 

3.2.4.  Auto IP with DHCP 

GW5120 can obtain network configuration such as IP address, Gateway address and subnet mask 
from DHCP server.    By default, the DHCP client function is disabled on GW5120, user can activate 
the DHCP functions by the following steps. 
 

„

 

Execute 

SerialManager 

utility 

„

 

Click on the 

IP address

 (of GW5120)   

„

 

Click “

Config

” to pop-up the static IP Dialog Window 

„

 

Check on ”

Auto IP

” 

„

 

Click “

Config Now

” (GW5120 will restart and obtain the IP from the DHCP server 

automatically) 

 

3.3. TCP/IP Port Number 

The default TCP/IP port numbers of serial port is 

4660

(1

st

 port) & 

4661

 (2

nd

 Port), and it is associated 

with the serial port 

COM1 

and 

COM2

 on configuration menu. After the Ethernet connection is 

established to GW5120 with TCP port 4660 (or 4661), the data of user’s application are transmitted 
transparently to GW5120 and vice versa. 

 

Summary of Contents for GW5120














































































Reviews: