background image

User’s Manual 

Wireless Serial Server GW5120

 

 

 

Copyright © 2009 Neteon Technologies, Inc. 

All rights reserved.   

33 

 

6.2.3. SNMP Settings 

 

Operation: [Main]

Æ

[2 Networking]

Æ

[3 SNMP Settings] 

Select 

SNMP Settings

 by press “

3

” 

Networking page:

” to enter 

SNMP Settings page. 

SNMP can 

be enable/disable, and network identification can be also set on 

SNMP Settings page.

 The 

changes will not become effective until GW5120 is restarted 
GW5120 supports get/set SNMP parameters, which are 

SysName

 (System Name), 

SysLocation

 

(System Location) and 

SysContact 

(System Contact). These will response and supply basic 

system information from standard SNMP query. SNMP system parameters set by enter the 
corresponding menus and values. For example, 

enter 2

 for changing the 

SysName 

then enter the 

desired name.   

 

Fig 44. SNMP Settings by Telnet 

 

6.3. Wireless Configuration 

Operation: [Main] 

Æ

 [3 Wireless Settings] 

Select Wireless Settings by press “

3

” on Main Menu; the following screen shall appear (

Fig. 45

). 

IP,

 

Netmask,

 

Gateway

IP

 

mode

, and 

Region 

can be set

 

by enter the corresponding menu and 

corresponding values. 

 

 

Fig 45. Configure Wireless Settings by Telnet 

Summary of Contents for GW5120














































































Reviews: