background image

Configure a Computer To Access the
Print Server

Before using the PS110/PS113 on your network, each computer that needs to access the print
server must have:

A connection to the network.

If a Windows computer, the printer added using the 

NETGEAR Add Printer Wizard.

Either the printer driver software already installed or, if this is a new printer, access to the
printer driver software (either on a CD or downloaded to a disk). 

To install the Add Printer Wizard (for a non-administrative computer):

Note: You can skip ahead “To configure
computers...” if you have already installed the
NETGEAR software on this computer. You do
not need to install the Add Printer Wizard on
any Macintosh computer.

1.

Insert the 

PS110/PS113 Printer Server Resource

CD in the CD-ROM drive. 

NETGEAR Print

Server Software Installation

wizard starts up

automatically. If it doesn’t, double-click 

My

Computer

, double-click your CD-ROM drive,

and double-click 

Setup.exe

.

2.

Follow the instructions in the installation wizard to install the software.

3.

When asked, select only the 

NETGEAR Add Printer Wizard

.

4.

Click 

Finish

.

7

Summary of Contents for PS110 - Print Server - Parallel




















Reviews: