background image

 

 

12 

7.Important Maintenance Instruction 

Kindly pay attention to the following in order to achieve the best maintenance of the product: 

• Keep the equipment dry. Rain, moisture and various liquids or water may contain minerals that can corrode electronic circuits. 

In case the device is wet, please dry it completely. 

• Do not use or store in dusty or dirty areas. This way can damage its detachable parts and electronic components. 

• Do not store in excessive heat place. High temperatures can shorten the life of electronic devices, destroy batteries, and deform 

or melt some plastic parts. 

• Do not store in excessive cold place. Otherwise, when the temperature rises to normal temperature, moisture will form inside 

which will destroy the board. 

• Do not throw, knock or shake the device. Treating equipment roughly can destroy internal circuit boards and delicate structures. 

• Do not wash with strong chemicals, detergents or strong detergents. 

• Do not paint the device. Smudges can make debris block detachable parts up and affect normal operation. 

• Do not throw the battery into the fire to prevent the battery from exploding. 

    Damaged batteries may also explode. 

 

All the above suggestions apply equally to your device, batteries and accessories.   

If any device is not operating properly. 

Please take it to the nearest authorized service facility for repairing. 

Summary of Contents for R720C














Reviews: