background image

WOS-2x1 / WOS-2x2 

 

Rev. 6

 

 
 

 

 

 

 

                                                   
Network Electronics ASA, Thorøya, 3204 Sandefjord, Norway, Tel.:+47 33 48 99 99 Fax: +47 33 48 99 98 
E-mail: support@network-electronics.com - Web: http://www.network-electronics.com 
 
Technical specifications are subject to be changed without notice 
 
 
  

21

 

 

50

 

 

It is assumed that while the product is in normal use, any batteries associated with real-time clocks or battery-backed RAM will 
be replaced at the regular intervals. 

The EFUP relates only to the environmental impact of the product in normal use, it does not imply that the product will continue 
to be supported for 50 years. 

 

Recycling information 

Network Electronics provides assistance to customers and recyclers through our web site 

http://www.network-electronics.com

. Please contact Network Electronics’ Customer Support for 

assistance with recycling if this site does not show the information you require.   
Where it is not possible to return the product to Network Electronics or its agents for recycling, the 
following general information may be of assistance: 

 

Before attempting disassembly, ensure the product is completely disconnected from power and 
signal connections. 

 

All major parts are marked or labelled to show their material content. 

 

Depending on the date of manufacture, this product may contain lead in solder. 

Some circuit boards may contain battery-backed memory devices.

 

  

Summary of Contents for WOS-2x1






















Reviews: