background image

1.

Posts 

(4)

 - Left - 10651, Right - 10652

2.

Post Caps 

(4)

 

- 10611

3.

Arches 

(4)

 

- Left - 10653-1, Right - 10654-1

4.

Arch Keystones

 

(

10836)

,

 

 Inserts

 

(10837)

,

 and Lids

 

(10668-1)

 

(2

 of each

)

5.

Keystone Bottom Plates 

(2)

 

- 10666-1

6.

Arch Rafters 

(6)

 

- 10655-1

7.

Side Panel Horizontal Bent Top Rails 

(2)

 

- 10656-1

8.

Side Panel Horizontal Mid-Rails 

(2)

 - 

10657-1

9.

Side Panel Horizontal Spindles Short 

(8)

 

- 10658-1

10.

 

Side Panel Vertical Spindles Long - Left 

(2)

 - 10659-1

11.

 

Side Panel Vertical Spindles Short - Middle 

(2)

 

- 10661-1

 

12.

 S

ide Panel Vertical Spindles Long - Right 

(2)

 - 10600-1

 

13.

 

Side Panel Horizontal Bottom Rails

 (2)

 - 10662-1

14.

 

Ground 

Mounting Extensions 

(4) 

 - 10844

15.

1 1/2 Self-Auguring Stainless Steel Screws 

(24) 

- 20005

  

Tools You Will Need

• Cordless Drill
• Hammer
• Tape Measure
• Level
• Stool or Short Ladder
• Shovel

General Information

 Read Instructions through carefully before

beginning assembly.

• When assembling components, place on a non-abrasive surface

(i.e. shipping box) 

to avoid scratching.

• We recommend an area approx 10ft.x 8ft. 

(3 m x 2.5 m) 

for unobstructed assembling.

• You should not need to use excessive force when assembling components.

ASSEMBLY INSTRUCTIONS

The Florence Arbor / Arch

15

89.6 in

(228 cm)

42 in

(107 cm)

49 in

(124 cm)

20 in

(

51 cm)

24 in

(

61 cm)

4

6

3

2

1

14

10

9

8

7

13

1

Not to Scale

81.8in

(208  cm)

Please read through before starting assembly.

IMPORTANT:  CHECK THE INSIDE OF YOUR POSTS FOR ALL MATERIALS.

Check Box for These Contents 

In the event of missing or defective parts please call our customer service dept. at 

1 800 282 9346

 (Mon. to Fri. 8:00 AM to 4:00 PM EST).

(UK Tel: 

(44) 2038 687160 

(Mon. to Fri.  1:00 PM to 10:00 PM GMT).

5

L

R

12

11

V2.

2

/

072417

www.newenglandarbors.com 

www.newenglandarbors.co.uk

Summary of Contents for The Florence

Page 1: ...tool or Short Ladder Shovel General Information Read Instructions through carefully before beginning assembly When assembling components place on a non abrasive surface i e shipping box to avoid scratching We recommend an area approx 10ft x 8ft 3mx2 5m for unobstructed assembling You should not need to use excessive force when assembling components ASSEMBLY INSTRUCTIONS The Florence Arbor Arch 15 ...

Page 2: ...ges on either side of the bottom of the insert This will connect the bottom of the arches to the insert Seal the bottom hole on the keystone by inserting the bottom plate as provided Install the top cap on the arch keystone Push down firmly so the cap locks into position Repeat for other arch Insert arch rafters 6 into the holes on the arches until they bottom out inside the arches There are locki...

Page 3: ...e that there are Left and Right side posts as indicated with the L and R at the top of the respective posts Repeat for other side panel 1 Assemble the Side Panels 2 3 4 5 6 7 1 2 3 4 6 Set out one side panel Insert the assembled arch through the holes at the top of the posts Do the same for the other side panel You will need a helper Adjust the opening width to 42in between the posts arbor allows ...

Page 4: ... into position and level it both vertically and horizontally Backfill the holes with the excavated soil to cover the anchors 1 2 Complete B 1 above with the exception of excavating the holes at least 6in 15 cm wide x 18in 46 cm deep Fill holes with wet cement within 3in 8cm of your grade you will need 2 bags of pre mix concrete purchase separately Carefully move the arbor back into position 1 2 Us...

Reviews: