*This is a quick-start guide and does not replace operations manual. Please refer to operations manual for detailed instructions and further information.
RMP5134 Rev A ©2017 Aerosolv Incorporated
aero
solv
AEROSOL
CAN RECYCLING
®
aero
solv
®
OPERATION
USING THE AEROSOLV SYSTEM:
WEAR SAFETY GOGGLES WHILE OPERATING AEROSOLV.
INSERT AEROSOL CAN
Insert aerosol can, NOZZLE END DOWN,
into housing sleeve, so that shoulder of
can rests on gasket. For 1” “mini-cans”,
push shoulder of can beyond gasket. Be
sure to remove cap from aerosol can prior
to insertion.
LOWER TOP PLATE
Lower the sliding top plate and FIRMLY
engage against plastic sleeve or bottom
of “jumbo” can. TIGHTEN lock knob.
PUSH HANDLE DOWN
Push handle down firmly until
completely depressed and HOLD IN
PLACE while can releases initial
pressure and contents. Allow the
contents of the can to drain into the
collection drum (about 20 seconds).
For safety, after removing the last
punctured can, lower sliding top to rest
on plastic sIeeve and tighten lock knob
to seal collection drum. For “jumbo”
cans, replace plastic sleeve prior to
lowering sliding top plate.
MAINTENANCE TIPS:
Thread into 2" bung, rotate
clock wise until ground support
plate firmly engages drum rim.
PUNCTURING UNIT
Thread directly to 3/4"
bung of drum.
FILTER
Attach ring terminal of Anti-
Static Wire to brass screw on
Ground Support Plate of
Puncturing Unit.
Attach other end of Anti-Static
Wire to any nearby confirmed
ground source, ex. metal pipe.
*OSHA requires that liquid
storage vessels be grounded
to prevent static.
ANTI-STATIC WIRE
Always operate outdoors or in a well ventilated area.
INSTALLATION
When puncturing “jumbo” cans, remove
white plastic sleeve from housing, then insert
can as pictured.
The first and only aerosol can recycling technology to be verified by
the joint U.S. EPA and California EPA Environmental Technology
Verification program (ETV).
aerosolv
®
PUNCTURING UNIT
•
Periodic cleaning and lubrication of the puncture pin
will assure years of trouble-free use. With constant,
heavy usage, the puncture pin should be cleaned and
lubricated once a month.
To clean or replace puncture pin, remove bridge pin at
uppermost point of handle. Entire handle mechanism and
puncture pin can be removed.
•
Gasket deterioration will occur when venting aerosol
paints and aggressive solvents, requiring periodic
gasket replacement. To assure proper seal during
usage, check gaskets frequently and replace as
required.
To replace gasket: remove plastic sleeve, pull out old gasket,
fold and insert new gasket, press into place.
FILTER
•
Replace Activated Carbon Cartridge after every 750
cans punctured. Remove spent Activated Cartridge by
turning counter-clockwise while holding lower
Coalescing Cartridge in place.
•
Replace entire filter every 9 months or after
puncturing 2250 spent aerosol cans.
*This is a quick-start guide and does not replace operations manual. Please refer to operations manual for detailed instructions and further information.
RMP5134 Rev A ©2017 Aerosolv Incorporated
aero
solv
AEROSOL
CAN RECYCLING
®
aero
solv
®
OPERATION
USING THE AEROSOLV SYSTEM:
WEAR SAFETY GOGGLES WHILE OPERATING AEROSOLV.
INSERT AEROSOL CAN
Insert aerosol can, NOZZLE END DOWN,
into housing sleeve, so that shoulder of
can rests on gasket. For 1” “mini-cans”,
push shoulder of can beyond gasket. Be
sure to remove cap from aerosol can prior
to insertion.
LOWER TOP PLATE
Lower the sliding top plate and FIRMLY
engage against plastic sleeve or bottom
of “jumbo” can. TIGHTEN lock knob.
PUSH HANDLE DOWN
Push handle down firmly until
completely depressed and HOLD IN
PLACE while can releases initial
pressure and contents. Allow the
contents of the can to drain into the
collection drum (about 20 seconds).
For safety, after removing the last
punctured can, lower sliding top to rest
on plastic sIeeve and tighten lock knob
to seal collection drum. For “jumbo”
cans, replace plastic sleeve prior to
lowering sliding top plate.
MAINTENANCE TIPS:
Thread into 2" bung, rotate
clock wise until ground support
plate firmly engages drum rim.
PUNCTURING UNIT
Thread directly to 3/4"
bung of drum.
FILTER
Attach ring terminal of Anti-
Static Wire to brass screw on
Ground Support Plate of
Puncturing Unit.
Attach other end of Anti-Static
Wire to any nearby confirmed
ground source, ex. metal pipe.
*OSHA requires that liquid
storage vessels be grounded
to prevent static.
ANTI-STATIC WIRE
Always operate outdoors or in a well ventilated area.
INSTALLATION
When puncturing “jumbo” cans, remove
white plastic sleeve from housing, then insert
can as pictured.
The first and only aerosol can recycling technology to be verified by
the joint U.S. EPA and California EPA Environmental Technology
Verification program (ETV).
aerosolv
®
PUNCTURING UNIT
•
Periodic cleaning and lubrication of the puncture pin
will assure years of trouble-free use. With constant,
heavy usage, the puncture pin should be cleaned and
lubricated once a month.
To clean or replace puncture pin, remove bridge pin at
uppermost point of handle. Entire handle mechanism and
puncture pin can be removed.
•
Gasket deterioration will occur when venting aerosol
paints and aggressive solvents, requiring periodic
gasket replacement. To assure proper seal during
usage, check gaskets frequently and replace as
required.
To replace gasket: remove plastic sleeve, pull out old gasket,
fold and insert new gasket, press into place.
FILTER
•
Replace Activated Carbon Cartridge after every 750
cans punctured. Remove spent Activated Cartridge by
turning counter-clockwise while holding lower
Coalescing Cartridge in place.
•
Replace entire filter every 9 months or after
puncturing 2250 spent aerosol cans.
