background image

                                                                                                                                       

 

                                                                                                                                                                                                                                           

            604100501000902

 

Website:

 

http://www.anpe.cn

                                                                                                                                                                                                                                                 

Address:

 

New

 

Power

 

industrial

 

Park,

 

Luhe

 

Economic

 

Development

 

Zone,

 

Nanjing,

 

China

 

Service

 

Tel:

 

+86(25)

84459479

                                                                                                                                                                                                                                                                                                                                                                 

Postcode:

 

211500

 

 

Dimension 

Width × Height× Length

7.4 mm × 95.2 mm × 70 mm 

 

 

 

Installation 

 The apparatus can be mounted on a 35 mm standard 

rail corresponding to DIN EN 60715, they must be 
snapped onto the rail, and never slanted or tipped to 
the side. 

 Requirements for installation 

In the safe zone, surge protective devices and safety 
barrier can be installed in the same or different cabinet, 
but can not be installed on the same track side by 
side. 
The cables (and wires) associated with the safety and 
the hazardous area should be wired and laid 
separately. 
 
 
 
 
 

 

 

 Installation steps are as follows: 

                               

Installation 

 

Make the metal bayonet locked into the guide rail, 
push the SPD in the rail as the direction of the arrow 
in the above. 

 Removing steps are as follows: 

Removing

 

First, pry the metal lock off the rail with screwdriver as 
arrow shown, pull downward the springs, and rotate 
the SPD, then remove it. 

 

Connections 

 Using M3 screwdriver;

 

M3

 

 

 Wire size is 0.2 mm

2

2.5 mm

2

;

 

2.5 mm

2

 

 

 Maximum torque of the screw is 0.5 N.m;

 

Max. 0.5 N.m

 

 

Attentions 

 The current Input Isolated Safety Barriers was 

constructed in protection degree IP 20 and must 
therefore be protected from undesirable ambient 
conditions (water, small foreign objects). It is suitable 
for installed in control room or high density field 
cabinet, convenient for installation and displacement. 

 The devices were designed for use in pollution degree 

2 and overvoltage category III as IEC/EN 60664-1. If 
used in areas with higher pollution degree, the devices 
need to be protected accordingly. 

 Installation position shall not be affected by strong 

mechanical vibration, impact and electromagnetic 
induction from signal terminal and power supply, 
should conformity with the requirements on 
electromagnetic interference resistance of products in 
Class 3 industrial field atmosphere stipulated in IEC 

61000-4, and the atmosphere shall be free from 
gases that are corrosive to metal and plastic 
components. 

 Before installation, please check the surge protector is 

intact or not. If have any damage, it should not be 
installed. 

 Only using the SPD according to this document, if 

more than the rated value, SPD and other device are 
likely to be damaged. 

 Devices must only be repaired directly by the   

 

manufacturer. Tampering with the apparatus is 
dangerous and therefore forbidden. 

 

Supplements 

 The apparatus must be installed, connected and 

adjusted by qualified personnel in non-hazardous area 
according with the instruction manual. 

 If faults cannot be eliminated, the apparatus must be 

taken out of operation and protected from being 
placed in service again inadvertently. Devices must 
only be repaired directly by the manufacturer. 
Tampering with the apparatus is dangerous and 
therefore forbidden.   

 The operator must strictly comply with the relevant 

local safety standards and guidelines. 

 If there is any content difference between the 

specification and the website or sample, the 
instructions shall prevail. We reserve the rights to 
change or update the product information without prior 
noticing the users. 

 

Reviews: