background image

4 Configurations on Web Interface

Caller Prefix

Called Prefix

Set a prefix for caller number. The prefix’s length is less than or equal 
to that of the caller number, which helps to match the caller number of 
this call. If caller number is 2001, the caller prefix can be 200 or 2. 
‘any’ means match any caller number.

Set a prefix for called number. The prefix’s length is less than or equal 
to called number, which helps to match the called number. If called 
number is 008675526456659, the called prefix can be 0086755 or 00. 
‘any’ means match any called number.

Calls to

Determine the call is routed to a port, a port group, an IP trunk or a SIP
server.

Stripped Digits

The number of digits which are lessened from the left of the caller

from Left

number

Stripped Digits

The number of digits which are lessened from the right of the caller

from Right

number

Prefix to Add

The prefix added to the caller number after its digits are lessened.

Suffix to Add

The suffix added to the caller number after its digits are lessened.

4.12.3

 

Tel

 

 IP/Tel Called

On the 

Tel

 

 IP/Tel Called

 page, you can set rules for manipulating the called number of Tel

IP/Tel calls.

Figure 4-12-3 Add Tel

 

 IP/Tel Called Number Manipulation

Gateway-128o User Manual

  

65

Summary of Contents for FXO-128o



























































































Reviews: