v. 04.14.16
Connecting to the NextCentury Cloud via WiFi:
1.
Enter the Network Settings page by pressing the settings
icon and then the Network Settings icon.
2.
Press the WiFi settings icon.
3.
Press the WiFi Network icon.
4.
Choose the preferred WiFi network.
5.
Press the Connect icon.
6.
Enter the Password (if necessary) and press done.
The Gateway will connect to the WiFi network and then to the
NextCentury Cloud.
4|Gateway LED Operation
The GW-201 Gateway comes equipped with two LED lights on the
front panel. Figure 4 and Figure 5 show what the different LED
patterns indicate.
Power Indicator
LED Pattern
Descipiton
Solid Red
Loss of Power
Blinking Red
Gateway is Reseting (Self-Healing)
Solid Green
Powered On but not connected to
NextCentury Cloud
Solid Blue
Powered On and connected to NextCentury
Cloud
Blinking Blue
Powered On and Property Programming
being performed from website
Figure 4 Power Indicator LED Table
RF Indicator
LED Pattern
Descipiton
1x Fast Red Blinks
Sending/Receiving 3
rd
Party Message
1x Fast Green Blinks
Sending/Receiving RE-201 Repeater or TR-
201 Transceiver Message
Figure 5 RF Indicator LED Table
4.1 - Power Indicator
When the Gateway is plugged in, the Power Indicator
(Figure 1-A) will be solid green indicating the device is
powered on but not connected with the NextCentury
Cloud. A solid blue Power Indicator (Figure 1-A) signifies
the device is powered on and has connected with the
NextCentury Cloud. The Power Indicator will turn red if a
loss of power occurs. If the Gateway is being reset, the
Power Indicator (Figure1 –A) will blink red. A blinking blue
Power Indicator (Figure 1-A) shows power is on and the
property programming is being performed from the
website.
4.2 - RF Signal Indicator
When the Gateway is sending or receiving messages from
a 3
rd
Party cable, the RF Indicator (Figure 1-B) will briefly
flash red. When indicating that the Gateway is sending or
receiving messages to and from an RE-201 Repeater or a
TR-201 Transceiver, the RF Indicator (Figure 1-B) will
briefly flash green.
5|Television and Radio Interference
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
6|FCC Part 15 and Industry Canada
Compliance
This device complies with part 15 of the FCC Rules and Industry
Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
This portable equipment with its antenna complies with FCC’s and
IC’s RF radiation exposure limits set forth for an uncontrolled
environment. Users are advised to maintain a separation distance of
20cm (this will be generated from our MPE report) to comply with
FCC and IC RF exposure limits.
Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas
produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
Cet équipement portable avec son antenne se conforme aux limites
d'exposition aux radiations RF du FCC et du IC, énoncées pour un
environnement non contrôlé. Les utilisateurs sont conseillé de
maintenir une distance de séparation de 20 cm (ceci sera généré
depuis notre rapport de MPE) pour se conformer aux limites
d'exposition RF du FCC et du IC.
