background image

 

                                                                  

Contact:

 

Support@Nexus21.com

 

Toll Free:

 (866) 500-5438 

Phone:

 (480) 951-6885 

Fax:

 (480) 951-6879 

                  

 

 

 

 

 

 

 

 

 

Revised: 6/23/15

 

 

Below is a parts list describing all of the items included with the Model L-45 Lift System. You may also 
wish to refer to the dimensional diagram shown on “Supplemental Page A” (at the end of this 
document). 
 
Before beginning assembly and installation, please make sure that you have all items included on the 
list.  If any parts are missing or damaged, please contact Nexus 21. Our contact information is shown 
at the top of this page. 

Parts List 

             
 
       
 
 
 
 
 
 
 

        

1.  

L-45 Lift Column                                    

2.  

Screen Support Bracket                         

3. 

Base Plate Bracket (2)

 

         (28 ¾” x 7” x 3 ¾”)                                                

 

(6.4 ” x 15.7”)

                                              

(6 ¼” x 2”) 

 
 
 
 
 
 
 
 

        

4. 

Upper Support Bracket  

                       5.  

Upper Support Bracket Base                    

6.  

Screen Back Plate                             

              (3” x 3 ½”)  

 

 

 

 (5 1/8” x 7”)

                                                 

(32” x 9”)  

                                                     

                                                                

 

 
 
 
 
 
 

   7. 

Lower Support Bracket                        

8. 

Top Plate Bracket                                   

9.  

Vertical Mounting Bars (2) 

 
             (10” x 4” x 2 ½”)                                     (18” x 

4 ½- 6 ½”

)                                                    

(20” x 1”)

 

 

NOTE:

   Items 6 & 9 are included in the “Nexus 21 Standard TV Mount” package.

 

 

Summary of Contents for L-45

























Reviews: