background image

Where to Go from Here

Visit 

ni.com/compactriodevguide

 for an overview of programming practices and examples for

your CompactRIO system.

Specifications

The following specifications are typical for the range -40 °C to 70 °C unless otherwise noted.
These specifications are for the reconfigurable embedded chassis only. For the controller and
I/O module specifications, refer to the operating instructions for the controller and I/O
modules you are using.

Reconfigurable FPGA

cRIO-9101 and cRIO-9102

Number of logic slices

5,120

Equivalent number

11,520

Available embedded RAM

81,920 bytes

cRIO-9103 and cRIO-9104

Number of logic slices

14,336

Equivalent number

32,256

Available embedded RAM

196,608 bytes

Timebases (40, 80, 120, 160, or 200 MHz)

Accuracy

±100 ppm maximum

Frequency dependent jitter

40 MHz

250 ps

80 MHz

980 ps

120 MHz

970 ps

160 MHz

960 ps

200 MHz

950 ps

Power Requirements

These power requirements are for a fully loaded chassis and exclude the power requirements
of the controller and the I/O modules in the chassis. For more information about the controller

12

  | 

ni.com

  | 

NI cRIO-9101/9102/9103/9104

Summary of Contents for cRIO-9101

















Reviews: