5.13 - Total or partial deletion of memory
This procedure allows you to choose under point 05 the data that you want to delete.
5.13.1 - Procedure performed with a transmitter memorised in “Mode I”
Before starting the procedure, bring the awning (or shutter) to the midpoint of its stroke.
01.
n
key pressed and wait for the motor to perform 2 movements. Upon completion, release the key.
02.
s
key pressed and wait for the motor to perform 3 movements. Upon completion, release the key.
03.
n
key pressed and wait for the motor to perform 3 movements. Upon completion, release the key.
04.
t
key pressed and wait for the motor to perform 3 movements. Upon completion, release the key.
05.
•
To cancel the entire memory
s
and
t
.
.
•
To delete only the memorised transmitters
.
•
To delete only the limit switch heights (“0”, “1”, “2”, “S”) and intermediate heights (“H”)
you want to adjust the limit switch heights again, using a different procedure than the one used previously.
n
key pressed and wait for the
motor to perform 5 movements. Upon completion, release the key.
Note
– When performing the procedure, at any time you can cancel it by keeping the
n
and
t
keys pressed simultaneously for 4 seconds. Otherwise, do not press
any key and wait 60 seconds for the motor to perform 6 movements.
5.13.2 -
Procedure performed with an unmemorised transmitter
Before starting the procedure, bring the awning (or shutter) to the midpoint of its stroke.
01.
.
02.
n
on an unmemorized tramsitter pressed for 8 seconds. Now release the button.
03.
.
04.
Now run the procedure in paragraph 5.13.1.
2
sec.
ON
OFF
01
02
END
8
sec.
New
I – – – – – – – – – – – – – –> max 15 sec. – – – – – – – – – – – – –>I
I – – – –> max 60 sec. – – – –>I
03
Paragraph 5.13.1
01
02
03
04
05
2
sec.
ON
OFF
02
Note
– When performing the procedure, at any time you can cancel it by keeping the
n
and
t
keys pressed simultaneously for 4 seconds. Otherwise, do not press
any key and wait 60 seconds for the motor to perform 6 movements.
5
sec.
01
04
03
02
5
sec.
5
sec.
all
data
only
05
05
END
“0”
“1”
“H”
05
END
END
5
sec.
5
sec.
5
sec.
2
3
3
3
5
5
sec.
5
5
This deletion must be performed only when
you want to adjust the limit switch heights
again, using a different procedure than the one
used previously. Whereas, if you want to ad-
just heights with the same procedure, it is not
necessary to delete them from memory.
EN
English –
10
Summary of Contents for E Fit L
