5.8 - Adjusting height (“H”) for partial opening/closing
The motor can manage up to 30 partial openings/closings, each called “H height”. These heights can only be adjusted after adjusting limit switches “0” and “1”. The
following procedure makes it possible to adjust one “H” height at a time.
Warning
– If you want to change the position a given “H” height that is already memorized, repeat the present procedure by pressing at point 06 the key associated
with that height.
Before beginning the procedure, bring the awning (or shutter) to the “H” height you want to memorize.
01.
n
key pressed and wait for the motor to perform 2 movements. Upon completion, release the key.
02.
n
key pressed again and wait for the motor to perform 4 movements. Upon completion, release the key.
03.
s
and
t
keys simultaneously and wait for the motor to perform two movements. Upon completion, release the keys.
04.
Fine adjustment of position
: Perform key pulsing on the
s
key and
t
key until the awning (or shutter) is brought to the partial height you want (at each pulse
the awning, or shutter, moves a few millimetres).
05.
n
key pressed and wait for the motor to perform 3 movements. Upon completion, release the key.
06.
•
: on the transmitter you are using for this procedure, keep the
s
and
t
keys pressed simultaneously and wait for the mo-
tor to perform 4 movements. Upon completion, release the keys.
•
: on the new unmemorized transmitter keep the desired key pressed and wait for the motor to perform 4 movements. Upon
completion, release the key.
5
sec.
01
04
02
03
“
H
”
5
sec.
05
06
END
8
sec.
5
sec.
“
H
”
4
2
5
sec.
2
3
fine regulation
Note
– When performing the procedure, at any time you can cancel it by keeping the
n
and
t
keys pressed simultaneously for 4 seconds. Otherwise, do not press
any key and wait 60 seconds for the motor to perform 6 movements.
5.9 - Memorising a SECOND (third, fourth, etc.) transmitter
To perform these procedures you must have a transmitter (“old”) already memorised.
5.9.1 - Memorising a second transmitter “Mode I”
– This procedure memorises the new transmitter in “Mode I”, regardless of the Mode in which the old to transmitter was memorised.
Before starting the procedure, bring the awning (or shutter) to the midpoint of its stroke.
01.
(on the new transmitter) keep the
n
key pressed for 8 seconds and then release it (in this case the motor does not perform any movement).
02.
(on the old transmitter)
n
key, provided it has already been memorized.
03.
n
.
.
If the motor performs 6
movements, it means that its memory is full.
Note
– When performing the procedure, at any time you can cancel it by keeping the
n
and
t
keys of the old transmitter pressed for 4 seconds.
8
sec.
New
0,5
sec.
Old
X 3
New
01
02
03
END
0,5
sec.
3
fine adjustment
7
– English
EN
Summary of Contents for E Fit L
