77
PL
Mostek Mostek
Pozycja
Założony
Wejście Fototestu podłączone do wyjścia Fototestu centrali.
Wejście Fototestu podłączone do wyjścia SCA centrali; lub wejścia Fototestu odłączonego jeśli
Zdjęty
centrala nie posiada ani Fototestu ani wyjścia SCA (Uwaga: Możliwe jest tylko z JP3 na TX
wyłączonym)
Przerwanie promienia podczerwieni powoduje otwarcie styku FOTO
Uaktywnienie listwy krawędziowej powoduje otwarcie styku STOP i po 1,5s styku STOP1
Przerwanie promienia podczerwieni powoduje otwarcie styku FOTO
Uaktywnienie listwy krawędziowej powoduje otwarcie styku FOTO i po 1,5s styku STOP i STOP1.
Stosować w centralach, które nie posiadają funkcji zmiany kierunku ruchu po interwencji STOP.
Zdjęty
JP2
Mostek Pozycja
Opis
Założony
Moc nadajnika dostosowana do bram o długości do 15 metrów.
Zdjęty
Moc nadajnika dostosowana do bram o długości maksymalnej do 7 metrów.
Założony
Przełącza na transmisję danych WOLNA po 10 sekundach po zakończeniu ruchu (patrz
również JP3)
Zdjęty
Przełącza na transmisję danych WOLNA po 90 sekundach po zakończeniu ruchu (patrz
również JP3)
Założony
Po zakończeniu ruchu przełącza na transmisję danych WOLNA
Zdjęty
Nigdy nie przełącza na transmisję WOLNA ale pozostaje zawsze w trybie SZYBKA.
Tabela 1: Mostki w nadajniku TX
JP1
JP2
JP3
Tabela 2: mostki na odbiorniku RX
JP1
Założony
3.3) Połączenia elektryczne
W tym rozdziale opisane są połączenia elektryczne i przedstawione są również niektóre schematy połączeń w zależności od typu
centrali zastosowanej w automatyce. W przypadku niepewności nie używać produktu i zażądać wyjaśnień w Serwisie Technicznym
firmy Nice.
Podłączenie
Rodzaj przewodu Maksymalna długość
Opis
12
÷
24V
2x0,5mm
2
30m
Zasilanie odbiornika; prądem stałym lub zmiennym
Fototest
2x0,25mm
2
30m
Wejście dla testu rozpoczęcia ruchu; może być podłączone
do prądu stałego lub zmiennego.
Styki wyjść
2x0,25mm
2
30m
Styki przekaźników wyjścia; zwykle zamknięte (NC) kiedy
odbiornik jest zasilany i jest w stanie aktywnym (patrz tabela 4)
Tabela 3: Spis połączeń
Wyjście
Styk przekaźnika Opis
FOTO
Zamknięty
Nie ma przeszkód i odbiór danych z TX jest prawidłowy.
Otwarty
Są przeszkody i odbiór danych z TX nie jest prawidłowy.
Wyjście FOTO (fotokomórka) ma być podłączone do wejścia centrali, które powoduje zmianę kierunku ruchu, zwykle
przeznaczonego da czujnika obecności typu D.
STOP
Zamknięty
Listwa krawędziowa podłączona do TX nie jest naciśnięta.
Otwarty
Listwa krawędziowa podłączona do TX jest pod naciskiem.
Wyjście STOP ma być podłączone do wejścia centrali, które powoduje zatrzymanie i ewentualnie zmianę kierunku ruchu,
zwykle przeznaczonego dla urządzeń zabezpieczających reagujących na nacisk PSPE.
STOP1
Zamknięty
Listwa krawędziowa podłączona do TX nie jest naciśnięta.
Otwarty
Po 1,5 sekundy jeżeli listwa podłączona do TX jest naciśnięta.
Wyjście STOP1 ma być podłączone do wejścia centrali, które powoduje zatrzymanie i ewentualnie zmianę kierunku ruchu, zwykle
przeznaczonego dla urządzeń zabezpieczających reagujących na nacisk PSPE
W przypadku braku drugiego wejścia w centrali można:
•
Wykorzystać wyjście STOP1 do sterowania przekaźnikiem o właściwej mocy tak, aby odciął zasilanie bezpośrednio w silniku
(patrz rysunek 18).
•
nie wykorzystywać wyjścia STOP1 i wyłączyć JP2 w RX, tym sposobem uaktywnienie listwy krawędziowej powoduje otwarcie
styku FOTO gwarantując również w tym przypadku 3 kategorię odporności na usterkę.
Tabela 4: Opis wyjść RX