background image

21

EN

EC DECLARATION OF CONFORMITY

Note

–This Declaration of Conformity contains the individual declarations of conformity for the specified products; it was updated on the issue

date of this manual and the text herein has been drawn up for editorial purposes. A copy of the original declaration for each product can be
requested from Nice S.p.a. (TV) I.

The undersigned, Lauro Buoro, in the role of Managing Director, declares under his sole responsibility, that the product:

Manufacturer’s name :

Nice S.p.a.

Address

:

Via Pezza Alta 13, Z.I. Rustignè, 31046 Oderzo (TV) Italy

Type

:

Receiver and receiver-transmitter for remote control of automations for doors, gates, shutters, 
awnings, rolling shutters and similar applications.

Models

:

OXI, OXIT, OXIFM, OXITFM

Accessories

:

conform with the requirements of the EC directive:

• 1999/5/EC; DIRECTIVE 1999/5/EC OF THE EUROPEAN PARLIAMENT AND COUNCIL of 9 March 1999 regarding
radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity

According to the following harmonised standards
Health protection: EN 50371:2002;
Electrical safety: EN 60950-1:2006;
Electromagnetic compatibility : EN 301 489-1V1.6.1:2006; EN 301 489-3V1.4.1:2002
Radio range: EN 300220-2V2.1.2:2007

Lauro Buoro

(Managing director)

Summary of Contents for NICEONE OX2 SERIES























Reviews: