background image

3

EN

ENGLISH

Mod.

Frequency

Function

Connection

OXI

433.92 MHz

Receiver

Connector type

OXIFM

868.46 MHz

Receiver

Connector type

OXIT

433.92 MHz

Receiver-transmitter Connector type

OXITFM

868.46 MHz

Receiver-transmitter Connector type

OX2

433.92 MHz

Receiver

with 6-core cable

OX2FM

868.46 MHz

Receiver

with 6-core cable

OX2T

433.92 MHz

Receiver-transmitter with 6-core cable

OX2TFM 868.46 MHz

Receiver-transmitter with 6-core cable

1

PRODUCT DESCRIPTION AND 
INTENDED USE

This receiver is part of the series “

NiceOne

” produced by Nice

spa. The receivers in this series are destined for use on the
control units fitted on systems for the automation of gates,
garage doors and road barriers.

Any use other than as

specified herein is to be considered improper and is
strictly prohibited! The manufacturer denies all liability for
damage deriving from improper use of the product and
use other than as specified in this manual.

Various models are available, with the specifications as stated
in the table below.

1.1

– 

The 

NiceOpera

” 

system

The receivers in the series 

NiceOne 

are part of the “

Nice-

Opera

” system. This system has been designed to simplify

the programming phases, use and maintenance of the de -
vices normally used in automation systems. The system com-

prises various software and hardware devices capable of
intercommunicating via radio, by means of the “

O-Code

encoding system or a “physical” connection via cable.
The main devices that make up the NiceOpera system are:

– NiceOne transmitters;
– NiceOne receivers;
– O-box programming unit;
– Control units and gearmotors with “T4 Bus”;
– O-View programmer for devices with “T4 Bus”.

IMPORTANT

– For further details on all functions of the

NiceOpera system and interdependency of the various
devices in the system, refer to the general manual “Nice-
Opera System Book”, also available on the Internet site
www.niceforyou.com.

Notes to table:

The frequencies 433.92

MHz and 868.46 MHz are
not compatible.

– The letter “

T

” in the model

name indicates a receiver with
built-in transmitter.

www.ApolloGateOpeners.com  |  (800) 878-7829  |  Sales@ApolloGateOpeners.com

Summary of Contents for NICEONE OX2 SERIES























Reviews: