EN
English –
7
DISPOSAL OF THE PRODUCT
This product is an integral part of the automation, and therefore, they must
be disposed of together.
As for the installation operations, at the end of the life of this product, the dis-
mantling operations must be performed by qualified personnel.
This product is made from different types of materials: some can be recycled,
others must be disposed of. Please inform yourselves on the recycling or dis-
posal systems provided for by the laws in force in your area, for this category of
product.
CAUTION!
– some parts of the product can contain polluting or dangerous sub-
stances which, if dispersed in the environment, may cause serious harm to the
environment and human health.
As indicated by the symbol at the side, it is forbidden to throw
this product into domestic refuse. Therefore, follow the “sepa-
rated collection” instructions for disposal, according to the meth-
ods provided for by local regulations in force, or redeliver the
product to the retailer at the moment of purchase of a new, equiv-
alent product.
CAUTION!
– the regulations in force at local level may envisage heavy sanctions
in case of abusive disposal of this product.
To keep the level of safety consistent and to guarantee maximum life of the en-
tire automation it is necessary to maintain it regularly.
The maintenance must be performed in line with the safety instructions of this
manual and according to what is set out by the laws and regulations in force. For
the gear motor a programmed maintenance within no more than 6 months is re-
quired.
Maintenance operations:
01.
Disconnect any sources of electricity.
02.
Check the status of deterioration of all the materials which make up the au-
tomation with particular attention to signs of erosion or oxidation of the
structural parts: replace the parts which do not provide sufficient guaran-
tees.
03.
Check the screw connections are sufficiently tight.
04.
Check the bolt and endless screw are suitably greased.
05.
Check the wear of the moving parts and, if necessary, replace used parts.
06.
Reconnect the sources of electrical power and perform all the tests and
checks envisaged in chapter 5.
For the other devices present in the system refer to the individual instruction
manuals.
PRODUCT MAINTENANCE
6
05.
Using the control or shutdown devices envisaged (key selector switch, con-
trol buttons or radio transmitters), perform a number of opening, closing
and stopping tests of the gate and check it behaves as it should;
06.
Check the correct operation of all the safety devices one by one in the sys-
tem (photocells, sensitive edges, emergency shutdown, etc.) and check the
gate behaves as it should;
07.
Command a closing manoeuvre and check the force of the impact of the leaf
against the end of the mechanical limit switch. If necessary, try to unload the
pressure, finding a setting which gives better results;
08.
If the dangerous situations caused by the movement of the leaf have been
protected by limiting the force of impact the force must be measured as re-
quired by regulation EN 12445.
Note
– The gear motor is not provided with torque setting devices, such regu-
lations are done by the Control unit.
• Putting into operation
This can occur only after having performed, with positive results, all the inspec-
tion phases of the gear motor and other devices present. To put it into opera-
tion refer to the instructions manual of the control unit.
IMPORTANT
– It is forbidden to put into partial or provisional operation
.
Type:
electromechanical gear motor for gates or doors with leaf opening
Power input:
24 V
Maximum absorption:
3,5 A
Nominal absorption:
2 A
Maximum absorbed power:
85 W
Nominal absorbed power:
50 W
Protection grade:
IP 44
Travel:
320 mm
Speed loadless:
0,018 m/s
Speed loaded:
0,013 m/s
Maximum thrust:
1500 N
Nominal thrust:
500 N
Operating temperature:
-20 °C to +50 °C
Cycles h at nominal torque:
40
Durability:
estimated between 80,000 and 250,000 cycles of manoeuvres
according to the conditions set out in Table 2
Insulation class:
A
Dimensions (mm):
770 x 98 x 95 h
Weight (kg)
: 6
TECHNICAL FEATURES OF THE PRODUCT
CAUTIONS: •
The technical features set out refer to an ambient temperature of
20°C (± 5°C). • Nice S.p.a. reserves the right to make alterations to the product
any time it deems it necessary, keeping the same functionality and destination
of use.
12
13
www.metalines.com
sales@metalines.com
