8 - 33
4. Input the compensation value of the SFB wheel position on the Groove & SFB adjustment
screen.
1) Call up the MENU screen.
2) Align the pointer (
→
) to “Groove & SFB adjustment” and press
.
3) Align the pointer (
→
) to the desired item.
To adjust the front SFB in beveling:
Set the parameter “SFB Wheel Pos. (BVL, F)” to 0.0 mm.
To adjust the rear SFB in beveling:
Set the parameter “SFB Wheel Pos. (BVL, R)” to 0.0 mm.
To adjust the front SFB in flat edging:
Set the parameter “SFB Wheel Pos. (FLT, F)” to 0.0 mm.
To adjust the rear SFB in flat edging:
Set the parameter “SFB Wheel Pos. (FLT, R)” to 0.0 mm.
4) Input the compensation value of the SFB
wheel position.
To decrease the chamfering amount (move
the wheel off the lens), press
.
To increase the chamfering amount (close
the wheel to the lens), press
.
5. Go back to the MENU screen.
Press
.
6. Go back to the Layout screen.
Press
twice.
7. Repeat Steps 1 - 6 until the chamfering wheel contacts the front edge of the lens and the
front SFB becomes 0.
8. Reset “SFB Width” 0.00 mm set in Step 1 to the desired SFB value.
ޓޓ㧿㧲㧮ޓ㨃㨕㨐㨠㨔㧔㨎㨢㨘㧘㨞㨑㨍㨞㧕ޓޓޓ㧦ޓ㧗㧜㧚㧟㨙㨙
ޓޓ㧿㧲㧮ޓ㨃㨕㨐㨠㨔㧔㨒㨘㨍㨠㧘㨒㨞㨛㨚㨠㧕ޓ㧦ޓ㧗㧜㧚㧞㨙㨙
ޓޓ㧿㧲㧮ޓ㨃㨕㨐㨠㨔㧔㨒㨘㨍㨠㧘㨞㨑㨍㨞㧕ޓޓ㧦ޓ㧗㧜㧚㧟㨙㨙
ޓޓ㧿㧲㧮ޓ㨃㨔㨑㨑㨘ޓ㧴㨑㨕㨓㨔㨠ޓޓޓޓޓޓ㧦ޓ㧜㧚㧜㧜㨙㨙
ޓ
ޓ
ޓޓ㧿㧲㧮ޓ㨃㨔㨑㨑㨘ޓ㧼㨛㨟㧚㧔㧮㨂㧸㧘㧲㧕ޓ㧦ޓ㧜㧚㧜㧜㨙㨙
ޓޓ㧿㧲㧮ޓ㨃㨔㨑㨑㨘ޓ㧼㨛㨟㧚㧔㧮㨂㧸㧘㧾㧕ޓ㧦ޓ㧜㧚㧜㧜㨙㨙
ޓψ㧿㧲㧮ޓ㨃㨔㨑㨑㨘ޓ㧼㨛㨟㧚㧔㧲㧸㨀㧘㧲㧕ޓ㧦ޓ㧜㧚㧜㧜㨙㨙
ޓޓ㧿㧲㧮ޓ㨃㨔㨑㨑㨘ޓ㧼㨛㨟㧚㧔㧲㧸㨀㧘㧾㧕ޓ㧦ޓ㧜㧚㧜㧜㨙㨙
Summary of Contents for LE-9000DX Express
Page 1: ...NIDEK PATTERNLESS EDGER LE 9000EX Express LE 9000DX Express OPERATOR SMANUAL...
Page 17: ...2 9 or or Top view...
Page 19: ...2 11...
Page 153: ......
