background image

                

TESTERS

 

EC2620 / EC2630 / EP2000 / PH2620 / PH2630 / PH2720

                

_____________________________________________________________________________________________

 

4

 

 

 
INTRODUCTION

  

 

Congratulations for buying one of the most innovative and easy to use Pocket Tester. 
 
Pocket testers series 1 and 5 are very handy for the routine measurements in all applications where 
fast indication of measurement is required. 
 
These  Testers  are  specially  designed  for  applications  like:  Agriculture,  water  and  waste  water 
treatment,  Hydroponics,  Aquaculture,  Environmental  monitoring,  Food  and  beverage 
manufacturing, Cooling towers, Printing, Education etc. 
 
Tester series 1 is basic one with fixed sensor and only two keys for all functions. 
 
Tester series 5 is advanced version with replaceable sensor, multicolour backlight display and 3 key 
for all functions. 
 
 

SAFETY INSTRUCTIONS 

  
 

       

Read this instruction manual carefully before using your new tester.  

 
       The membrane of pH electrode is made of glass and can be danger in case it breaks.  
       To avoid damage check the electrode tip after each measurements.  
 
       Replace all batteries together with the same type.  
 
       

The manufacturer of these instruments can’t be held responsible for any 

improper use.  

 
       Verification of the measuring results is the responsibility of the operator and the manufacturer  
       doesn

’t respond to any direct of indirect damage occurred while using this instrument.

  

 
  

DISPOSAL OF ELECTRONIC DEVICES 

 

The electrical and electronic equipment marked with this symbol cannot be 
disposed of in public landfills. 
According to the UE Directive 2002/96/EC, the European users of electrical 
and electronic equipment can return it to the dealer or manufacturer upon 
purchase of a new one. 
The illegal disposal of electrical and electronic equipment is punished with 
an administrative fine. 

 
 

 
 

Summary of Contents for EC2620














Reviews: