Light Output
240 lm (100%)| 120 lm (50%) |24 lumens (10%)
Light Source
Cree XP-G LED
Running Time
2.5h (100%)| 6h (50%) |15h (10%)
Charge Time
4h
Battery
18650 Li-ion rechargeable
Product Size (mm)
L130 x Dia.25
Product Weight (kg)
0.139
Boxed Size (mm)
230x150x60mm
Boxed Weight (kg)
0.470kg
NS Part No
NSTRACKER
240
Supplied with
Flashlight, wrist strap, battery, charger cradle, mains and
vehicle adaptor
The Cree® LEDs can last up to 50, and seldom need to be replaced. If there is any
malfunction of LED, please contact Nightsearcher Limited or an authorised distributor.
INSTALLING THE BATTERY
•
Unscrew the tail cap.
•
Insert the battery pack into the barrel, with the positive (+) end of battery towards the
flashlight head.
•
Fasten the tail cap tightly. Press the tail cap push button to test.
NOTE:
Always insert the battery into the flashlight according to the positive (+) and
negative (-) mark. Reverse polarity will damage the flashlight and the battery.
BATTERY CHARGING
•
Ensure the flashlight is switched OFF and remove the battery.
•
Connect the charger to AC power supply; the LED indicator (located on the charging
tray) will turn RED.
•
Insert the battery into the charging tray,
ensuring correct polarity.
•
When the battery is fully charged, the LED indicator on the AC power supply will turn
GREEN. The LED on the charging tray will remain RED
•
This charger has a built-in protection system, long time charging will not cause battery
overload.
•
These batteries can be charged at any time without causing “memory affect” or
damage to the battery. However, less than 9 hours continuous charging is suggested
for safety.
NOTE:
Always insert the battery into the charging cradle according to the positive (+) and
negative (-) mark. Reverse polarity will damage the charger and the battery
The ON/OFF switch is located in the tail of the flashlight;
•
Press the tail cap switch and the flashlight will turn ON (100%)
•
Press the tail cap switch halfway and the flashlight will switch to LOW (50%)
•
Press the tail cap switch halfway again and the flashlight will switch to FLASHING
NOTE:
In any mode press the tail cap fully and the flashlight will switch OFF
•
Use a small brush or blow dry air to clean any dust inside the reflector.
•
Use lens cleaner and cotton swab, to remove any fingerprints on the lens.
•
To prevent the O-ring from drying to ensure for threads operating smoothly, please
apply petroleum jelly to these surfaces two or three times a year.
•
The non-anodised metal groove between the tail cap and the barrel must be cleaned
periodically to ensure a good electrical contact.
•
The O-ring prevents water from getting into the flashlight.
•
Do not use the flashlight for diving; it is not suitable for the high pressure underwater
environment.
•
If water gets inside the flashlight, remove the battery immediately and place in a well
ventilated area.
The instructions hereunder list the safety measures for operating your flashlight, battery and
chargers:
BATTERY
•
Do not expose the battery to excessive heat, to do so may cause an explosion.
•
Do not use metal objects to short circuit the positive and negative end of the battery.
•
Do not dispose of the battery in the domestic waste, please use the correct method of
disposal.
•
Do not solder directly on to the battery.
•
Do not let the battery become wet or immerse the battery in water.
•
If there is evidence of leakage from the battery do not touch the battery with bare
hands. If your skin or your clothes come into contact with any leaked substance from
the battery, clean with water immediately.
•
Should any leaked substance from the battery come into contact with your eyes, do
not rub your eyes. Rinse with clean water immediately and seek medical assistance.
•
Keep the battery away from children.
•
The operating temperature range of the flashlight’s battery is listed below :
Charging: 0°C to 45°C / Discharging: -20°C to 60°
GENERAL
•
Do not use any chargers other than those provided. Failure to do so could cause fire,
electrical shock or personal injury
•
Never use a damaged charger or charger with damaged lead. Should the charger or
its lead become damaged, replace the charger immediately.
•
Do not shine the flashlight directly into people’s eyes, as it may damage their eyesight.
•
If the charger is not in use, please disconnect it from the AC power supply. Do not
leave the battery on charge for more than one week, as this will shorten the battery
life. Battery leakage may occur if the battery is over charged.
•
Do not pull the lead of the charger when disconnecting it from the AC Power supply.
•
Do not use an extension lead. Connect the charger directly into an electrical socket.
•
Always make sure the flashlight system is disconnected from any power sources and
turned off when performing any routine cleaning or maintenance. Do not try to repair
the unit or charger yourself.
•
In case of any problems or questions please contact NightSearcher Limited or an
authorised distributor.
SPECIFICATION
LED ASSEMBLY REPLACEMENT
BATTERY INFORMATION
ON / OFF AND MODE OPERATION
FLASHLIGHT MAINTENANCE
SAFETY PRECAUTIONS
