background image

 Introduction 

 

 

Introduction 

 

Thank you for purchasing a Nikon product. 

This instruction manual is written for users of the Nikon Microscope ECLIPSE Series Teaching Head/Multi Teaching 
Head. 

To ensure correct usage, read this manual carefully before operating this product. 

 

  No part of this manual may be reproduced or transmitted in any form without prior written permission from Nikon. 

  The contents of this manual are subject to change without notice. 

  Although every effort has been made to ensure the accuracy of this manual, errors or inconsistencies may remain. If 

you note any points that are unclear or incorrect, please contact your nearest Nikon representative. 

  Some of the equipment described in this manual may not be included in the set you have purchased. 

  If you intend to use any other equipment with this product, read the manual for that equipment too. 

  If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may 

be impaired. 

 

 

 

 

 

 

 

 

 

 

 

   

Symbols Used in This Manual 

The following symbols are used in this manual. 

Symbols for Safety 

  WARNING 
  CAUTION 

Highlights important information that should be noted for safety. Read “Safety Precautions” for 
details. 

Other Symbols 

 

Indicates information you should be aware of in using this product, as well as other useful information. 

 

 

Summary of Contents for Eclipse Series






















Reviews: