background image

- vi - 

Cautions Concerning Use 

1. Installation 

Location 

To avoid mis-operation and to peform safe and precise measurement, be sure to observe the 
following points when installing this system. Be especially careful not to pinch your fingers, etc., 
when installing the system. 
•  Install the system in a clean environment. Dust and oily vapors can have a clear and adverse 

impact on the performance of the system. Dirt and corrosion on the guide surfaces of the stage 
in particular can cause a deterioration in the precision of the system. 

•  Install the system in a location where the temperature ranges from 10 to 35 °C and where the 

humidity is less than 70%. Installation in a hot, humid location can result in condensation and 
malfunctions. 

•  Install the system in a controlled temperature environment (i.e., an environment that is not 

subject to rapid changes in temperature). Temperature changes can cause measurement errors. 

•  Before selecting the installation location, study the requirements described on page 17. 
•  Install the system in a location with little vibration. 
•  Install the system in a location that is not subject to sudden voltage fluctuations or electronic 

noise. 

•  If the ventilation holes for the cooling fan in the controller are blocked, a malfunction or fire 

could result. 

•  Install the controller so that there is an open space of at least 20 cm between the rear panel of 

the controller and the nearest wall. Do not obstruct the ventilation openings on the front of the 
controller. 

•  Make sure that the main body and the side of the measurement stand are at least 20 cm away 

from the nearest wall. When setting up a personal computer rack or other equipment next to 
the main body or the side of the measurement stand, also provide a space of at least 20 cm. 
Failure to follow this instruction may lead to the risk of collision between the stage and a wall or 
object. 

 

2. Handle 

carefully 

This system is a precision instrument that requires careful handling. Striking the system or 
operating it in a reckless manner could damage the system. 

 

3.  Measurement and temperature 

Generally, the dimensions of a workpiece will change according to the temperature. (The amount 
of change depends on a coefficient that is inherent to the material.) The operation of this system 
is guaranteed over a wide temperature range, but in order to obtain stable and reproducible 
measurement results, the system should be used in an adequately controlled temperature 
environment with less temperature change. In addition, when using this system for the first time, 
be sure that you have allowed the system to become fully adjusted to the temperature 
environment. (Usually, this simply requires leaving the system in that temperature environment for 
about 24 hours.) 

 

4. Measurement 

stand 

The main body comes with a special measurement stand. If the special measurement stand is not 
used, be sure to use a stand with sufficient strength and rigidity. If a general-purpose working 
table is used, make sure it can withstand 1,000 kg of uniformly distributed load or more. 

 

Summary of Contents for HVBTR-1200































Reviews: