background image

 

8

X) Remove cables and re-attach case and four screws. 
 
Y) test again boot process and with NikonScan 
 
Z) test again a week later and / or burn-in for 48 hours  
 

Appendix A:

  

(to remove the black mechanism assy from the metallic-colored case structural assy) 
 
This additional disassembly may be required to remove the top light source module to clean front 
surface mirrors, both on top and bottom where the lens and sensor module is. 
 
i) remove the four screws on top module, place in vial #5 
 
ii) remove tiny black screw on front corner of structural assy, place in vial #6. Note the indexing of 
the top plate with other screw heads 
 
iii) remove three screws on bottom that attach the black mechanism to base of the structural assy, 
place in vial #6  
 
The whole black mechanism will slide out. This will facilitate cleaning access to especially dirty 
mirrors and lens 
 
iv) reverse procedure for re-assembly. The light source assembly is in elongated sliding slots. 
Fasten in the mid-position. 
 
 

IV. Warranty and Limits of Liability 

 
This procedure is provided on a "best-efforts" basis and there is no warranty whatsoever herein, 
and is provided "AS-IS." It requires a high-level of technical competence and mechanical dexterity, 
such as an "A+ Certification" Computer Technician plus 3 years experience, or equivalent, and 
demonstrated ability to handle and understand complex, delicate optical mechanisms and 
instruments. 
 
(ie practice of something simpler, like reviving a bad CD-ROM, CD player or VCR that is eating 
tapes). 
 
A prerequisite is being able to comfortably use Scott Mueller's "Upgrading and Repairing PCs," the 
1500-page defacto "Bible" by Que, documentation available from manufacturers on the internet, 
and having successfully built a custom-made computer from scratch (separate components). 
 

This is the Entire Agreement between the User and the Service Provider 

 
The User assumes all risk in using this document. If this procedure is used, the User specifically 
agrees to "hold harmless" from any and all liability alleged the responsibility of the Author, which 

Summary of Contents for LS-2000










Reviews: