ELECTRICAL SYSTEM
FORM NO. 56043089 / AquaRide
™
/ BRX 700 - 49
BATTERY SPECIFICATIONS
- Use a combination of multiple 2-volt cell units (wired in series) to construct a 36 Volt DC battery pack system.
- Nilfi sk-Advance recommended battery pack capacity is a 238 or 305 AH @ 20 Hour Rate deep cycle battery system (six 6V-batteries). Note: The
battery pack must fi t the battery compartment size listed in Specifi cations.
BATTERY CHARGER SPECIFICATIONS
- Use a 36 Volt DC output charger matching the DC battery pack voltage and the input AC line voltage supply being used.
- Always when selecting a battery charger follow the recommendation of the battery supplier to match the proper charger DC output amperage to
the amp/hour rating batteries being installed. This will prevent the battery pack from being over or under charged.
- The recommended 238 AH battery should be matched to a 36V, 20 Amp charger.
- The recommended 305 AH battery should be matched to a 36V, 25 Amp charger.
INSTALL THE BATTERIES
WARNING!
Use extreme caution when working with batteries. Sulfuric acid in batteries can cause severe injury if allowed to contact the skin or
eyes. Explosive hydrogen gas is vented from inside the batteries through openings in the battery caps. This gas can be ignited by
any electrical arc, spark or fl ame.
When Servicing Batteries...
•
Remove all jewelry.
•
Do not smoke.
•
Wear chemical goggles, rubber gloves and a protective apron.
•
Work in a well-ventilated area.
•
Do not allow tools to touch more than one battery terminal at a time.
CAUTION!
Electrical components in this machine can be severely damaged if the batteries are not installed and connected properly. Batteries
should be installed by Nilfi sk-Advance or by a qualifi ed electrician.
1 Remove the batteries from their shipping crate and carefully inspect
them for cracks or other damage. If damage is evident, contact
the carrier that delivered them or the battery manufacturer to fi le a
damage claim.
2 Turn the Master Key Switch (J) OFF (O) and remove the key.
3 To access the battery compartment tip the operator’s seat forward
and set the prop rod. Remove the battery cables from inside the
battery compartment.
4 Your machine comes from the factory with enough battery cables
to install six (6 volt), 305 Amp hour batteries. Using two people
and an appropriate lifting strap, carefully lift* the batteries into the
compartment tray exactly as shown on machine decal (Figure 1).
5
The terminals on the battery cables are marked “+” for positive and “-“
for negative. Install the battery cables as shown, with the terminals
marked “+” on the positive battery terminals and the terminals marked
“-“ on the negative terminals. Position the cables so the battery caps
can be easily removed for battery service.
6
Carefully tighten the nut in each battery terminal until the terminal will
not turn on the battery post. Then tighten the nut half an additional
turn. Do not over-tighten the terminals, or they will be very diffi cult
to remove for future service.
7
Coat the terminals and posts with spray-on battery terminal coating
(available at most auto parts stores).
8 Put one of the black rubber boots over each of the terminals and retain with supplied tie straps.
9 Connect the battery pack connector to the Machine Battery Connector (22) and close the operator’s seat platform.
*Note: Removal of the recovery tank can make battery installation easier.
FIGURE 1
Summary of Contents for 56314019
