INSTRUCTIONS FOR USE
8
9096910000(1)2006-09
MACHINE STRUCTURE - DESCRIPTION
Control panel (1)
- It is the area where machine controls are located, see Control and Switch Description paragraph.
Handlebar (2)
- Grasp it and use it to maneuver the machine.
Drive paddle (3)
- See Control and Switch Description paragraph.
Speed adjuster (4)
- See Control and Switch Description paragraph.
Battery charger data inspection window (5)
- See Battery Warning Light Description paragraph.
Battery charger cable (6)
- Connect it to the electrical mains to charge the batteries.
Battery charger cable holder (7)
- Use it to roll up the battery charger cable when it is not in use. Fasten the cable safely.
Solution rear filler neck (8)
- Open it to pour the solution/clean water (**) in the tank. Use only low-foam detergents.
Water removable filler hose (optional) (9)
- For easily filling the tank with water (**).
Squeegee lifting/lowering lever (10)
- To lift or lower the squeegee.
Deck lifting/lowering pedal (11)
- It has the following functions:
(11a) Deck lifting
(11b) Deck lowering
(11c) Extra pressure activation for
20D
e
X20D
(optional for
X24D
).
This function cannot be used for
20D
,
X20D
and
X24D
when equipped with cylindrical brush deck.
Battery connector (red) (12)
- It connects the batteries to the machine electrical system. It must be connected to the external
battery charger, when the machine is not equipped with on-board battery charger. This connector also works as EMERGENCY
switch, to stop immediately all functions. If necessary, grasp the handle and disconnect the connector by pulling it strongly.
Rear steering wheel (13)
- It allows the machine to steer.
Front wheels on fixed axle (14)
- They bear the machine weight. Driving wheels (*).
Squeegee vacuum hose (15)
- It conveys the recovery water from the squeegee to the recovery water tank. To easily clean it,
remove the plug (35).
Recovery water drain hose (16)
- It drains the recovery water from the tank.
Solution/clean water drain and level check hose (**) (17)
- It is equipped with level marks to check the solution/water level
in the tank. Disconnect the upper end to drain the tank.
Brush/pad-holder deck (18a, 18b, 18c)
- On the deck, brushes or pad-holders and the relevant motors are installed. Decks
are easy to remove (with tools) and can be replaced with other types of deck. Three types of deck are available: with one
brush/pad-holder, with two brushes/pad-holders, with two cylindrical brushes (for instructions, see the relevant paragraphs).
Brushes/pads (19a, 19b)
- According to the type of deck, the machine can be equipped with: brushes, pad-holders or cylindrical
brushes.
Solution/clean water tank (20)
- It contains the solution/clean water (**).
Recovery water tank (21)
- It contains the recovery water collected by the squeegee and vacuumed.
Recovery water tank cover (22)
- It hermetically closes the recovery water tank.
Can holder (23)
- Compartment to store a can or small objects.
Pocket (optional) (24)
- Elastic retainer for documents.
Squeegee (25)
- It collects the solution after scrubbing. Choose the squeegee according to the type of deck (see the relevant
paragraph).
Squeegee mounting handwheels (26)
- They fasten the squeegee to the machine.
Squeegee balance adjusting handwheel (27)
- To adjust the squeegee blade position.
Machine straight forward movement adjusting handwheel (***) (28)
- Turn it clockwise or counter-clockwise for machine
straight forward movement.
Battery connection diagram (29)
- It shows how to connect the batteries.
Recovery water tank cover (opened) -
By turning the retaining plate (32), it can be removed.
It can be opened in one of the following positions:
(30a) Opened to be cleaned.
(30b) Completely opened.
Tank cover gasket (31)
- The gasket must be integral for an efficient vacuuming of the recovery water.
Cover retaining plates (32) and (33)
- Turn the retaining plate (32) to remove the tank cover.
Serial number plate/technical data/conformity certification (34)
- It contains the machine data.
Plug for squeegee vacuum hose cleaning (35)
- Remove it to clean the vacuum hose.
Vacuum grid with automatic shut-off float (36)
- Keep it clean, to avoid a stuck in the vacuum system.
