background image

Electronic  Service

Manuals

This electronic document is provided as a service to our custom-
ers.  We do not create the contents of the information contained in
this document.  Should you have detailed questions pertaining to
the information contained in this document, you may contact Michco,
or the manufacturer which provided the original information in this
electronic deliverable.  Michco’s only part in this electronic deliver-
able was the electronic assembly process.

You may contact Michco through the following methods:

Phone (517) 484-9312 or (800) 331-3339 MI, OH, IN only

2011 N. High St.  -- Lansing, Michigan -- 48906

Fax: (517) 484-9836

Email: CustServ@Michco.com

Web site: www.Michco.Com

Parts Web site:  www.FloorMachineParts.Com

Order Parts on Line at:

www.FloorMachineParts.Com

Directly to Parts & Service:

By Email: 

Shop@Michco.com

By Fax: (517) 702-2041

By Voice: Use numbers above.

Serving the Cleaning Industry Since 1922

Notice: All copyrighted material remains property of original owners, all trademarks are property of respective
owners.  Manuals are subject to Manufacturer’s reproduction limitations.  Originals or reproductions were provided
by manufacturers through a request.  We make no warranty as to the correctness of information provided in this
document and you assume all risk.

Summary of Contents for DuraGloss 2000











Reviews: