background image

FORM NO. 56041466 / SELECTLINE 17TS / 20TS - 6

AFTER USE

1

Unplug the Power Cord, coil it and hang it from the Operator Hand Grips
(1).

2

Remove the pad holder or brush from the machine. Clean the pad or brush
and hang it up to dry. Allow buffing pads to dry completely before using
again.
Store brushes and pad holders separate from the machine. Never store
the machine with the pad holder or brush on the machine.

3

Wipe the entire machine with a clean, damp cloth. Wipe the underside of
the brush housing after wet use.

4

Inspect the entire machine and all accessories for damage. Perform any
required maintenance or repairs before storage.

5

Store the machine in a clean, dry place with the Handle locked in the
upright position.

TROUBLESHOOTING

SWIRLS ON THE FLOOR AFTER SCRUBBING

Floor not clean.

Incorrect solution.

Area not properly swept - debris in pad or brush.

Improper pad or brush for the job.

Moving the machine too fast.

Incorrect speed selected.

SWIRLS ON THE FLOOR AFTER DRY BUFFING

Moving the machine too fast.

Floor finish too soft.

Area not properly swept - debris in pad or brush.

Improper pad or brush for the job.

CIRCLES ON THE FLOOR

Machine standing still while the brush or pad is running.

FLOOR FINISH REMOVED

Improper pad... too aggressive.

Solution too strong.

MACHINE WOBBLES DURING OPERATION

Defective pad... one side is more dense than the other.

Machine left sitting on brush or pad for extended period of time causing
bristles or pad to “take a set”.

Pad not “seated” properly into pad holder bristles.

Warped block on brush or padholder - replace.

MACHINE DOES NOT RUN

Check plug for proper connection - on machine and at wall outlet.

Check building circuit breaker.

Call for service.

TECHNICAL SPECIFICATIONS (as installed and tested on the unit)

Model

SelectLine 17TS

SelectLine 20TS

Model Number

56636966

56636977

Motor

1.50 hp

1.50 hp

Transmission

Dual-Planetary

Dual-Planetary

Pad/Brush Speed

175 rpm / 275 rpm

175 rpm / 275 rpm

Pad/Brush Size

17” (43 cm)

20” (51 cm)

Wheels

5” (13 cm)

5” (13 cm)

Cord Length

50’ (15 m)

50’ (15 m)

Base Width

17.5” (44 cm)

20.5” (52 cm)

Height w/Handle

48” (123 cm)

48” (123 cm)

Net Weight (w/pad holder)

100lbs (45kg)

100lbs (45kg)

Summary of Contents for Kent SelectLine 17TS









Reviews: