ENGLISH
INSTRUCTIONS FOR USE
4
SC100 - 107412885
04/2015
WARNING!
–
Close attention is necessary when used near children.
–
Use only as shown in this Manual. Use only Nilfisk’s
recommended accessories.
–
Check the machine carefully before each use, always
check that all the components have been assembled
before use. If the machine is not perfectly assembled it
can cause damages to people and properties.
–
Take all necessary precautions to prevent hair, jewels
and loose clothes from being caught by the machine
moving parts.
–
Do not use the machine on incline.
–
Do not use the machine on slopes with a gradient
exceeding the specification.
–
Do not use the machine in particularly dusty areas.
–
Use the machine only where a proper lighting is
provided.
–
While using this machine, take care not to cause
damage to people or objects.
–
Do not bump into shelves or scaffoldings, especially
where there is a risk of falling objects.
–
The machine working temperature must be between 0 °C
and +40 °C.
–
The machine storage temperature must be between 0 °C
and +40 °C.
–
The humidity must be between 30 % and 95 %.
–
When using floor cleaning detergents, follow the
instructions on the labels of the detergent bottles.
–
To handle floor cleaning detergents, wear suitable
gloves and protections.
–
Do not use the machine as a means of transport.
–
Do not allow the brush to operate while the machine is
stationary to avoid damaging the floor.
–
In case of fire, use a powder fire extinguisher, not a
water extinguisher.
–
Do not tamper with the machine safety guards
and follow the ordinary maintenance instructions
scrupulously.
–
Do not allow any object to enter into the openings. Do
not use the machine if the openings are clogged. Always
keep the openings free from dust, hairs and any other
foreign material which could reduce the air flow.
–
Do not remove or modify the plates affixed to the
machine.
–
This machine cannot be used on roads or public streets.
–
Pay attention during machine transportation when
temperature is below freezing point. The water in the
recovery tank or in the hoses could freeze and seriously
damage the machine.
–
Use brushes supplied with the machine or those
specified in the Instructions for use Manual. Using other
brushes could reduce safety.
–
In case of machine malfunctions, ensure that these are
not due to lack of maintenance. If necessary, request
assistance from the authorised personnel or from an
authorised Service Center.
–
If the machine
• does not work properly
• is damaged
• has water or foam leaks
• has been left outdoors exposed to bad weather
conditions
• is wet or has been dropped into water
turn it off immediately and contact the Nilfisk Service
Center or a qualified technician.
–
If parts must be replaced, require ORIGINAL spare parts
from an Authorised Dealer or Retailer.
–
To ensure machine proper and safe operation, follow the
relevant scheduled maintenance table in this manual.
–
Do not wash the machine with direct or pressurised
water jets, or with corrosive substances.
–
The machine must be disposed of properly, because
of the presence of toxic-harmful materials (electronic
components, etc.), which are subject to standards that
require disposal in special centres (see the Disposal
chapter).
MACHINE DESCRIPTION
MACHINE STRUCTURE
(Figure 1)
1. Handle
2. Main switch
3. Start/stop push button
4. Solution push button, level 1
5. Solution push button, level 2
6. Empty solution tank warning LED
7. Pedal for release from parking position
8. Squeegee bar lifting/lowering pedal
9. Tank coupling and transport handle
10. Solution tank
11.
Solution tank filler plug
12.
Solution filter
13. Recovery tank
14. Cleaning deck
15. Brush engagement/disengagement lever
16. Cylindrical brush
17. Squeegee bars
18. Inspection lid
19. Recovery water vacuum hose
20.
Air filter cover
21. Recovery tank drain plug
22. Vacuum inlet plug
23. Brush/vacuum motor compartment
24. Rear wheels
25. Transport handle housing
26. Power supply cable holder
27. Power supply cable with connector
28.
Serial number plate/technical data/conformity certification
107412885(1)04-2015 A.indb 4
16/09/2015 16:54:38
