background image

19

ninjakitchen.com

18

ninjakitchen.com

 Plug in motor base and place on a clean, 

dry, level surface such as a countertop  

or table.

2  

Add liquid then ingredients to the 

Single-Serve Cup. 

DO NOT

 add 

ingredients past the 

MAX LIQUID

 line.

3    

Place the Hybrid Edge™ Blades Assembly 

on the top of the cup and turn clockwise 

to seal.

4  

Turn the cup upside down and install on 

the motor base by aligning the tab on 

the cup with the slots on the base. Then, 

rotate cup clockwise until it clicks. Once 

locked in place, press the Power button 

to turn unit on. The available program 

buttons will illuminate and the unit will 

be ready for use.

IMPORTANT:

 

Review all warnings on 

pages 4–7 before proceeding.

 

NOTE: 

Auto-iQ® programs have pauses and 

changes in speed throughout the cycle.

USING THE NUTRIENT EXTRACTION* CUP

5a  

If using an Auto-iQ program, use the 

dial to select the program that best 

suits your desired output, then press 

START/STOP. The preset feature will 

automatically stop at the end of the 

program. To stop the unit at any time, 

press START/STOP.

5b    

For Manual mode, press IQ/MANUAL. 

With speed 8 on the display, press 

START/STOP. Once the ingredients have 

reached your desired consistency, press 

START/STOP and wait for the unit to 

come to a complete stop. 

6  

Remove the cup from the motor base 

by turning it counterclockwise and then 

lifting up.

7  

Remove the blade assembly by twisting 

counterclockwise. 

DO NOT

 store blended 

contents with the blade assembly 

attached. Only use the Spout Lid or 

Storage Lid to cover. Exercise care when 

handling the blade assembly, as the 

blades are sharp.

9  

Turn the unit off by pressing the Power 

button. Unplug the unit when finished. 

Refer to the Care & Maintenance section 

for cleaning and storage instructions.

8  

To enjoy on the go, place the Spout Lid 

or Storage Lid onto the cup and twist lid 

clockwise until firmly sealed.

NOTE: 

If the unit is plugged in and powered 

on, but the cup and blade assembly are not 

properly installed, the timer will display “- -” 

and the motor will be disabled.

NOTE: 

Only speed 8 is available when 

using the Single-Serve Cup. 

* Extract a drink containing vitamins and minerals 

from fruits and vegetables

Summary of Contents for Foodi CO351B Series














Reviews: