background image

IMPORTANT INFORMATION:

For the most accurate results using TRUE METRIX:

•  Read all product instructions for use before testing.

•  Use of TRUE METRIX in a manner not specified in 

this Owner’s Booklet is not recommended and may 

affect ability to determine true blood glucose levels.

•  TRUE METRIX is an 

in vitro

 (outside body) 

quantitative system that is used for self-testing of 

human whole blood only.

•  Alternative site (forearm) testing should not be used to 

calibrate continuous glucose monitors (CGMs).

•  Alternative site (forearm) testing should not be used 

for insulin dose calculations.

•  Use only TRUE METRIX Self Monitoring Test Strips and 

TRUE METRIX Control Solution with the TRUE METRIX 

Self Monitoring Meter.

•  Remove only one test strip at a time from test strip 

vial. Recap vial immediately.

•  NEVER reuse test strips.  NEVER wipe test strips 

with water, alcohol or any cleaner. DO NOT attempt 

to remove blood or control solution from test strips 

or clean test strips and re-use. Reuse of test strips will 

cause inaccurate results.

•  NEVER add a second drop of sample to test strip. 

Adding more sample gives an error message.

•  Perform Control Tests before performing a blood 

glucose test for the first time.

3

TMX_OB_GutsENG_RE4NPD03r6.indd   3

7/15/15   3:37 PM

Summary of Contents for TRUE METRIX























































Reviews: