background image

Attention:

If the battery cannot be fully charged after 12 hours of charging, please stop charging 

the battery and contact your dealer. 

To maximize battery life, please keep the battery state-of-charge percentage within 

20% to 80%. 

The battery will lose more capacity in lower temperature conditions. To be more 

specific, the usable capacity at 15°F is 70%, 85% at 32°F, and 100% at 75°F. 

The optimum battery state-of-charge for storage is 50%. Storing battery with less than 

10% or more than 90% state-of-charge over a long period of time will cause 

irreversible capacity loss to the battery. 

The battery must be removed from the scooter for storage longer than one week. 

While in storage, please keep the battery at a temperature of 32°F to 68°F with a state-

of-charge between 30%-70%. It's advised to have at least one cycle of charge and 

discharge every 2 months to minimize battery capacity loss during storage. 

 

If the battery fails due to misuse or lack of proper maintenance as instructed, any 

implied warranty will be void.  

External Impacts may cause internal damage to the battery and may cause leakage, 

overheat, smoking, fire or explosion. 

27

Summary of Contents for M+
























































Reviews: