background image

1-4 Operation 

  Do  not  disconnect  the mains  cable  on the  UPS  system  or  the  building  wiring  outlet 

(shockproof  socket  outlet)  during  operations  since  this  would  cancel  the  protective 
earthing of the UPS system and of all connected loads.   

  The UPS system features its own, internal current source (batteries). The UPS output 

sockets or output terminals block may be electrically live even if the UPS system is 
not connected to the building wiring outlet.   

  In  order  to  fully  disconnect  the  UPS  system,  first  press  the  OFF/Enter  button  to 

disconnect the mains.   

  Prevent no fluids or other foreign objects from inside of the UPS system.   

1-5 Maintenance, service and faults 

  The UPS system operates with hazardous voltages. Repairs may be carried out only 

by qualified maintenance personnel.   

 

Caution

 - risk of electric shock. Even after the unit is disconnected from the mains 

(building wiring outlet), components inside the UPS system are still connected to the 
battery and electrically live and dangerous.   

  Before carrying out any kind of service and/or maintenance, disconnect the batteries 

and verify that no current is present and no hazardous voltage exists in the terminals 
of high capability capacitor such as BUS-capacitors.   

  Only  persons  are  adequately  familiar  with  batteries  and  with  the  required 

precautionary  measures  may  replace  batteries  and  supervise  operations. 
Unauthorized persons must be kept well away from the batteries.   

 

Caution

 - risk of electric shock. The battery circuit is not isolated from the input voltage. 

Hazardous voltages may occur between the battery terminals and the ground. Before 
touching, please verify that no voltage is present!   

  Batteries may cause electric shock and have a high short-circuit current. Please take 

the precautionary measures specified below and any other measures necessary when 
working with batteries:   

remove wristwatches, rings and other metal objects   

use only tools with insulated grips and handles.   

  When changing batteries, install the same number and same type of batteries.   

  Do  not  attempt  to  dispose  of  batteries  by  burning  them.  This  could  cause  battery 

explosion.   

  Do not open or destroy batteries. Escaping electrolyte can cause injury to the skin and 

eyes. It may be toxic.   

  Please replace the fuse only with the same type and amperage in order to avoid fire 

hazards.   

  Do not dismantle the UPS system.   

 

 

 

 

Summary of Contents for NUPS23 Series





















Reviews: