background image

34

35

Engli

sh

Română

The icon 

 and 

 

are flashing on LCD display. 

Alarm is sounding every 

second.

UPS is overloaded.

Remove excess 

loads from UPS 

output.

UPS is overloaded. 

Devices connected 

to the UPS are 

fed directly by the 

electrical network 

via the Bypass.

After repetitive 

overloads, the 

UPS is locked in 

the Bypass mode. 

Connected devices 

are fed directly by 

the mains.

Remove excess 

loads from UPS 

output first. Then 

shut down the 

UPS and restart it.

Fault code is shown as 49 

on LCD display and alarm is 

continuously sounding.

UPS is over input 

current.

Remove excess 

loads from UPS 

output.

Fault code is shown as 43 

and the icon 

 is lighting 

on LCD display. Alarm is 

continuously sounding.

The UPS 

shut down 

automatically 

because of 

overload at the 

UPS output.

Remove excess 

loads from UPS 

output and restart 

it.

Fault code is shown as 14 and 

the icon 

 is lighting 

on LCD display and alarm is 

continuously sounding.

The UPS 

shut down 

automatically 

because short 

circuit occurs on 

the UPS output.

Check output 

wiring and if 

connected devices 

are in short circuit 

status.

Fault code is shown as 01, 

02, 03, 11, 12, 13 and 41 

on LCD display and alarm is 

continuously sounding.

A UPS internal 

fault has occurred. 

There are two 

possible results:

1. The load is 

still supplied, but 

directly from AC 

power via bypass. 

2. The load is no 

longer supplied by 

power.

Contact service 

unit.

Battery backup time is shorter 

than nominal value.

Batteries are not 

fully charged.

Charge the 

batteries for at 

least 5 hours 

and then check 

capacity. If the 

problem still 

persists, consult 

your dealer.

Batteries defect.

Contact your 

dealer to replace 

the battery or 

replace them by 

yourself.

Fault code is shown as 2A 

on LCD display and alarm is 

continuously sounding.

The short circuit 

occurs on the 

charger output.

Check if 

battery wiring 

of connected 

external pack is 

in short circuit 

status.

Fault code is shown as 45 

on LCD display. At the same 

time, alarm is continuously 

sounding.

The charger does 

not have output 

and battery 

voltage is less than 

10V/PC.

Contact service 

unit.

Summary of Contents for Balder 1000








































Reviews: