background image

20

21

OUTPUT W:

 R, S and T output power in watt.

OUTPUT VA:

 R, S and T output power in VA.

OUTPUT W (%):

 R, S and T output power watt in percentage.

OUTPUT VA (%):

 R, S and T output power VA in percentage.

Total watt and VA:

 W(%)/Total VA(%): Total input load watt and VA in 

percentage.

BATT Voltage/Bus Voltage/Charging Current/Discharging Current:

 The real 

time value of DC related information.

Temperature: 

Temperature of R, S and T phases.

Measure screen page 3

INPUT W:

 R, S and T input power in watt.

INPUT VA:

 R, S and T input power in VA.

INPUT W (%):

 R, S and T input power watt in percentage.

INPUT VA (%):

 R, S and T input power VA in percentage.

Total W(%)/Total VA(%):

 Total input load watt and VA in percentage.

Input current:

 The real-time value of input current in R, S and T phases.

Output current:

 The real-time value of output current in R, S and T phases.

Input PF:

 The real-time value of input power factor in L1, L2 and L3 phases.

Output PF:

 The real-time value of output power factor in R, S and T phases.

3.2.4. Setting screen

This sub-menu is used to set the parameters of UPS. Touch the icon 

 to enter 

setting menu page. There are 2 options: Basic and Advanced. Touch the icon 

 

to return to main screen. Touch the icon 

 to go back to previous menu.

NOTE!

Not all settings are available in every operation mode. If the setting is not 

available in present mode, the LCD will keep its original setting parameter showed 

instead of changing the parameters.

3.2.3. Measure screen

Touch the icon 

 to enter measure page. Touch the icon 

 or 

 to 

browse information. Touch the icon 

 to return to main screen. Touch the 

icon 

 to go back to previous menu.

Measure screen page 1

LINE VOL:

 The real time value of R, S and T phase voltage, RS, ST, TR voltage 

and input frequency.

INVERTER VOL:

 The real time value of R, S and T inverter voltage, RS, ST and 

TR voltage and frequency.

BYPASS VOL:

 The real time value of R, S and T bypass voltage, RS, ST and 

TR voltage and frequency

OUTPUT VOL:

 The real time value of R, S and T output voltage, RS, ST and 

TR voltage and frequency

Measure screen page 2

Summary of Contents for Ranger 180KT


























Reviews: