background image

44

45

Storage and maintenance

5

5.1. Storage

Before storing, charge the UPS at least 7 hours. Store the UPS covered 

and upright in a cool, dry location. During storage, recharge the battery in 

accordance with the following table:

Storage Temperature

Recharge Frequency

Charging Duration

-25°C - 40°C

Every 3 months

1-2 hours

40°C - 45°C

Every 1 months

5.2. Maintenance

Maintenance,  all  repairs  and  service  must  be  performed  by  authorized 

personnel only. There are no user-serviceable parts inside the UPS. Please 

contact the technician that installed the UPS for maintenance services.

WARNING

  The UPS system operates with hazardous voltages. Repairs may be carried 

out only by qualified maintenance personnel.

  Even after the unit is disconnected from the mains, components inside 

the UPS system are still connected to the battery packs which are potentially 

dangerous.

  Before carrying out any kind of service and/or maintenance, disconnect 

the batteries and verify that no current is present and no hazardous voltage 

exists in the terminals of high capability capacitor such as BUS-capacitors.

  Only persons adequately familiar with batteries and with the required 

precautionary measures may replace batteries and supervise operations. 

Unauthorized persons must be kept well away from the batteries.

  Verify that no voltage between the battery terminals and the ground is 

present before maintenance or repair. In this product, the battery circuit is 

not isolated from the input voltage. Hazardous voltages may occur between 

the battery terminals and the grounding/earthing.

  Batteries may cause electric shock and have a high short-circuit current. 

Please remove all wristwatches, rings and other metal personal objects 

before maintenance or repair, and only use tools with insulated grips and 

handles for maintaining or repairing.

  When replacing the batteries, install the same number and same type of 

batteries.

  Do not attempt to dispose of batteries by burning them. This could 

cause battery explosion. The batteries must be deposed according to local 

environmental regulations.

  Do not open or destroy batteries. Escaping electrolyte can cause injury to 

the skin and eyes. It may be toxic.

  Please replace the fuse only with the same type and amperage in order to 

avoid fire hazards. 

  Do not disassemble the UPS system.

Summary of Contents for Ranger 180KT


























Reviews: