background image

 

 

22 

11.  SPECIALIZED  STIPULATIONS  FOR  THE  US-  AMERICAN 

MARKET 

 

The content in this chapter is specialized for the US-American market. 

 

a. 

Foreword/ Compliance

 

Operating  this  truck  requires  knowledge  which  can  be  acquired  from  this  instruction  handbook.  This 
handbook must be kept available throughout the entire period of use of the truck. 

 

YOU  MUST  BE  TRAINED  AND  CERTIFIED  TO  OPERATE  THIS  TRUCK!  READ  AND  OBEY  ALL 
WARNINGS AND INSTRUCTIONS IN THIS MANUAL AND ON THE TRUCK! 

 

Only  properly  trained operators  are  allowed  to  operate  a  powered  industrial  truck.  Your  employer  must 
train  you  and  certify,  that  you  are  qualified  to  operate  this  truck  (required  by  OSHA  §  1910.178).  The 
training  must  satisfy  OSHA  requirements  and  as  minimum  the  topics  mentioned  in  this  handbook. 
Depending  on  the  context  in  this  operating  manual,  the  user  can  refer  to  several  people,  including  the 
owner of the truck, anyone who leases or borrows this truck, and the operator as defined in ASME B56.1. 
Please pay attention to the section in ASME B56.1 concerning the operator. In this standard, it is defined 
that the safe operation is the responsibility of the operator (ASME B56.1-2003, Part II, section 5.1.1). You 
and others can be seriously injured or even killed if you don’t use this truck correctly. Before operating your 
truck, inspect your truck and ensure that it is in correct working order. This truck was designed and built to 
current industry and government standards. For more information see following:   
- ASME B56.1 (American Society of Mechanical Engineers) 
- OSHA §1910.178 (Occupational Safety and Health Act) 
- UL 583 (Underwriters Laboratory) 
- ANSI Z535.4 (American National Standards Institute) 

  This  sign  indicates  hazard  situations,  if  not  avoided,  will  result  in  serious  injury  or 

death.  The  instructions  or  precautions  to  this  message  must  be  observed  to  avoid  the  potential  risk of 
injury or death. 
 

  If not followed, warning indicates hazard situations which may lead to moderate injury. 

The instructions or precautions to this message must be observed to avoid the potential risk of injury or 
death. 
 

  If not followed, caution indicated situations which may lead to minor injury. Instructions 

or precautions must be observed to avoid minor injury. 
 
 
 
 

Summary of Contents for ACX 10E





























Reviews: