background image

 

 

NOTE 

It indicates notes on important matters and useful functions. 

 

CONSULTATION 

It indicates the necessity to refer to the instructions of this manual before   

performing any procedures.

 

GENERAL SAFETY INSTRUCTIONS 

Specific  warnings  and  cautions  for  potential  damages  to  personnel  and  machine  are 

notified as follows: 

 

DANGER! 

 

 

This machine must be operated by trained and authorized personnel according to the instructions of 

this manual. 

 

Before  performing  any  procedures  of  cleaning,  maintenance,  repair  or  replacement,  read  all  the 

instructions carefully, and ensure to turn off the machine and disconnect the battery connector. 

 

Do not operate the machine near toxic, dangerous, flammable and/or explosive powders, liquids or 

vapors. This machine is not suitable for collecting dangerous powders. 

 

Do not wear jewels when working near electrical components. 

 

Do not work under the lifted machine without safety support. 

 

Lead-acid  battery  may  emit  inflammable  gas  under  normal  use,  must  keep  the battery away  from 

sparks, flames, smokes and radiating, illuminating and burning objects. 

 

During charging, lead-acid battery may emit hydrogen gas which may cause explosion. Must keep 

the charging environment well-ventilated and away from naked flames. 

 

 

WARNING! 

 

 

Check  the machine  carefully  before  each use  to ensure  that all  parts  of  the  machine are installed 

correctly, otherwise it may cause harm to people or property. 

 

 

Please check if the values of voltage and frequency indicated on the serial number label match with 

the main power before using the charger. 

 

Do not move the machine by pulling the charger cable, do not let the cable pass through a closed 

door, or wind with sharp edges or angles, and do not let the machine run over the cord. Keep the 

battery charger cable away from heated surfaces. 

 

In  order  to avoid  fire, electric  shock  or  personnel  injury,  make  sure  that  the  machine  is off  before 

leaving. 

 

This  machine  is  not  intended  for  outdoor  use,  it  is  only  suitable  for  indoor  use,  please  store  the 

machine in a dry indoor environment when not in use. 

 

The storage temperature and working ambient temperature of the machine must be between 0-

40°C 

(32°F~104°F). The humidity must be between 30%-95%. 

 

Do not use the machine on a ramp that exceeds the specified slope.   

Summary of Contents for NR530
























Reviews: