background image

 

 

CHANGE AND IMPROVEMENT 

 

Our company is committed to the continuous improvement of the products and reserves the right to 

notify the improvements and changes of the products that have been sold. 

 

INTENDED USE 

 

This  floor  scrubber  can  be  used  in  commercial  and  industrial  environments,  and  it  is  suitable  for 

cleaning  smooth  and  hard  floors  (washing  and  sewage  collecting).  It  must  be  used  in  a  safe 

environment  by  a  qualified  operator.  This  scrubber  is  not  suitable  for  cleaning  outdoors  floors, 

carpets or rough floors. 

 

MACHINE IDENTIFICATION 

 

The model and serial number of this machine are marked on the identification label. The information 

on this label is very important, which is required to be provided when you order the accessories for 

the machine.   

 

TRANSPORTING AND UNCRATING 

 

Carefully  check  machine  for  signs  of  damage.  Report  damages  at  once  to  carrier.  Record  the 

damages on paper to reserve the right for compensation. 

After uncrating, check if the machine is equipped with the following items: 

1.  Technical documents, including operation manual; 

2.  Battery connecting cable. 

 

SAFETY 

 

The following symbols indicate potential dangers. In any case, please read this information carefully 

and take necessary precautions to avoid possible injury and property loss.

 

         

SAFETY SYMBOLS 

WARNING! 

Read all the instructions carefully before performing any operation   

on the machine. 

DANGER!

 

It indicates the danger that may cause death of the operator. 

 

WARNING! 

It indicates a potential hazard that may cause people injury and objects   

damage. 

 

CAUTION! 

It indicates a caution related to important or useful functions. 

Pay attention to the paragraphs marked by this symbol. 

 

 

Summary of Contents for NR530
























Reviews: