background image

 

20 

Installation environment 

In order to ensure the best operating performance, the battery need to be kept under normal working 
conditions:  between  0  and  40  degrees  Celsius  and  normal  humidity.  Avoid  excessive  temperature 
difference on both sides of the battery (more than 5

Emergency management 

Below are examples of several ways to deal with possible emergencies: 

 

In  case  of  Smoke  or  Ignition:  stop  to  use  equipment  immediately,  take  appropriate  actions 
according to working instructions and stay away from the scene. 

 

In case battery is immersed in water: stop to use equipment immediately, take appropriate actions 
according to working instructions and stay away from the scene. 

 

Products  produce  smell:  stop  to  use  equipment  immediately,  remove  the  battery  and  take 
appropriate  actions  according  to  working  instructions  and  stay  away  from  the  scene.  Avoid 
contact with any leaking liquids or gases out of the battery (in case of contact clean immediately). 

Necessary safety equipment 

 

Self-contained breathing apparatus and personal protective equipment. 

 

Sevofluoropropane fire extinguishing system. 

b.

 

Matters requiring attention (lithium battery) 

 

The charging function of batteries may be blocked by Battery Management System if temperature 
of cells inside the battery case is lower than +5

. Make sure the own temperature of battery is 

above this value and the temperature of the battery is even. 

 

Batteries are forbidden to charge at low temperatures, but they can be used in occasional low 
temperature environment (please refer to normal working conditions allowed for the truck), but 
their efficient capacity will be lower, which is a normal phenomenon. 
 

Ambient temperature 

Remaining discharge capacity of battery pack 

25

 

100% 

0

 

90% 

-20

 

70% 

-30

 

40% 

 

Note:

 Although the battery can be discharged at very low temperature, it is easy to generate 

condensate during the charging process, which will damage the internal electronic devices of 
the battery and create unpredictable hidden dangers. Batteries cannot be charged until they are 
slowly warmed up to minimum allowed temperature for activation of charging function (may take 
up to 4 hours in normal temperature conditions). Forced warming up (e.g., using of heaters, 
vents etc.) is forbidden. 
 
The dependence of actual capacity from environmental temperature is shown for reference only 
and can not be used as a commitment/allowance for low temperature operation, please refer to 
the Chapter 1 for correct application conditions 

 

 

The battery protection level is IP40, so please do not wash the battery directly with water. 

Summary of Contents for PSE12BD

































Reviews: