8
Nobles Quick Clean 12 (01/2014)
English
EN
MACHINE OPERATION
PRE-SWEEP
Sweep the area to be cleaned prior to operating the
machine.
PRE-SPRAY
:LWKWKHXVHRIDSXPSXSVSUD\HUSUHVSUD\WKHÀRRUZLWK
an approved Hard Surface Pre-Spray detergent. Only use
FRPPHUFLDOO\DYDLODEOHÀRRUFOHDQHUVLQWHQGHGIRUPDFKLQH
application. Follow proper mixing and handling instructions on
detergent bottle.
:$51,1*
'RQRWXVHÀDPPDEOHFOHDQLQJ
VROYHQWVZLWKPDFKLQH'RQRWSLFNXSÀDPPDEOHRU
combustible material or work in areas were they may be
present.
SET PRESSURE
While the trigger is activated on the hard surface tool and the
SXPSVZLWFKLVWXUQHGRQWXUQWKHSUHVVXUHDGMXVWPHQWNQRERQ
the front of the machine between 400-1200 PSI.
&$87,21
:KHQXVLQJDKDQGWRRORUFDUSHWZDQGDGMXVW
SUHVVXUHDFFRUGLQJWRDFFHVVRU\WRROVSHFL¿FDWLRQV
CLEANING WITH HARD SURFACE TOOL
1.
)ROORZVLWHVDIHW\JXLGHOLQHVFRQFHUQLQJZHWÀRRUV
2. Verify the vacuum hose and solution hose are securely
connected to the machine and hard surface tool.
3. Choose either the Glide Ring or the Brush Ring for the Hard
Surface Tool. Using the 3 tabs snap the desired ring onto
the Dome Housing of the Hard Surface Tool.
Glide Ring – man made tiles such as porcelain and ceramic.
Brush Ring – natural stone and non-man made surfaces with a
texture.
Read all instructions before using
this machine.
4. Ensure the vacuum break cover is closed when using the
Hard Surface Tool. If the Hard Surface Tool happens to
VWLFNWRWKHÀRRUGXHWRWKHYDFXXPVXFWLRQVOLGHWKH
vacuum break cover up. Once the Hard Surface Tool is loose
IURPWKHÀRRUFORVHWKHYDFXXPEUHDNFRYHU
5. Turn on the pump and vacuum switches. Turn on the Auto-
Dump switch if using this feature.
6. For optimum cleaning results pull trigger while moving the
Hard Surface Tool in a front to back motion.
7.
*RRYHUDUHDMXVWFOHDQHGZLWKYDFXXPRQO\VWURNHEHIRUH
moving to the next area.
NOTE:
Use defoamer any time foaming occurs in the recovery
tank to prevent damage to the motor or other components.
8. Monitor the water level in the solution tank. If the solution
tank runs dry, the pump must be reprimed.
9. When the solution tank is low, turn off all the switches,
HPSW\WKHUHFRYHU\WDQNDQGWKHQ¿OOWKHVROXWLRQWDQN
127(:KHQWKHUHFRYHU\WDQNLVIXOOWKHEDOOÀRDWVFUHHQZLOO
VKXWRIIWKHVXFWLRQWRSUHYHQWWKHPDFKLQHIURPRYHUÀRZLQJ
$OZD\VXVHGHIRDPHUWRSUHYHQWRYHUÀRZ7KHEDOOÀRDWVFUHHQ
may not work if there is too much foam in the tank. Always use
GHIRDPHUWRSUHYHQWRYHUÀRZ
10.
:KHQ¿QLVKHGZLWKWKHMREVKXWRIIDOOVZLWFKHV%HIRUH
disconnecting solution hose relieve the water pressure from
the Hard Surface Tool by holding the trigger on the Hard
Surface Tool.
Vacuum
Break Cover
Glide Ring
Brush Ring
Pump Switch
Auto Dump
Switch
Vacuum
Switch
