background image

5.1.4 Disposal for old battery 

Old battery must be recall or deposit at the safe-environmental area or special disposal area 

appointed by the local government, the department that dispose these scrap should be authorized. . 

 

 

As the electrolyte in battery is poisonous and corrosive, the man who operate the battery 

should be performed in overall and protection goggles to avoid body touching the acid solution of 
the battery. 

! In case that acid solution touches clothes, wash it immediately with plenty of water. If the skin 

or eye touch the acid solution, you should be not only washing with plenty water but also going to 
hospital immediately. The acid extravasations should be eliminated through neutralization 
treatment. 

 

5.2  Type of Battery  

The weight and the dimension of the battery can be known from the battery nameplate. 

! During replacement or assembly of battery, make sure the battery fixed in the case reliably. 

 

5.3  Battery indicator 
 

Battery capacity meter: 

Discharging value of battery is indicated on battery capacity meter, it has 

ten indicator bars that each one has 10% increase in sequence.   

With the consumption of battery capacity, the bright bars will descend downwards from the top. 

The mark of “Alarm” will appear when: The residual capacity of the battery against normal battery at 

the 30%. Now the battery is needed to charge. 

 

Capacity Sufficient

               

Charge Required

                     

Capacity Insufficient

 

 
 
 
 
 
 
 
 
 

 

5.4  Charge of Battery 

! the battery witch is non-use for a long time should be charged. Charge of battery must comply 

 

14

Summary of Contents for SPT15 Series



























Reviews: