NODOR I2030BK, Operating And Maintenance Instructions Manual

This appliance is not intended to be used via 

an external timer or a remote control system. 

The manufacturers decline any responsibility 

in the event of non-compliance with what is 

described above and the accident prevention 

norms not being respected and followed. 

To avoid all risk, if the power cable 

becomes damaged, it must only be 

replaced by the manufacturer, by 

an authorised service centre, or by 

a qualified electrician. 

OPERATING PRINCIPLE (Fig. 1) 

It exploits the electromagnetic properties of most cooking vessels.

The coil (inductor) which produces the electromagnetic field is 

operated and controlled by the electronic circuit. 

The heat is transmitted to food by the cooking vessel itself. 

The cooking process takes place as described below. 

-  loss of heat is minimum (high efficiency) 

-  the system stops automatically when the vessel is removed or 

even just lifted from the hob 

-  the electronic circuit guarantees maximum flexibility and fine 

adjustments. 

(Fig. 1) 

1  Vessel 

2  Induced current 

3  Magnetic field 

4  Inductor 

5  Electronic circuit 

6  Power supply 

User’s Instructions (Fig. 2) 

1  ON/OFF 

2  Minus – 

3  Plus + 

4  Cooking zone 

5  Setting level display

6  Zone selection lights

7  Lock key

8  Timer Display

Installation 

All operations relative to installation (electric connection) should be 

carried out by skilled personnel in conformity with the rules in force. 

As for the specific instructions see part pertaining to installer.

Switching the Touch Control ON/OFF 

After mains voltage is applied the control initializes for approx. 

1 second before it is ready for operation. 

After a reset all displays and LEDs glow for approx. 1 second. When 

this time is over all displays and LEDs extinguish and the control is 

in the stand-by mode. 

Press the ON/OFF (1) button to switch the touch control on. 

The cooking zone displays show a static “0“. 

If a cooking zone is in the “hot“ status, the display shows a static 

“H“ instead of “0“. The bottom right dot is blinking in 1 second 

intervals on all cooking zone displays to indicate that no cooking 

zone is selected at the moment. 

After switching-ON the electronic control remains activated for 20 

seconds. If no cooking zone or timer selection follows within this 

period of time, the electronic control automatically switches back 

into the stand-by-mode. The control can only be switched-ON if it 

identifies the ON/OFF key alone being operated. Should it recognize 

key activation other than that, the control remains in the standby- 

mode. 

If the child safety feature is active when switching on, all cooking 

zones show “L“, (LOCKED). If the cooking zones are in a “hot“ status, 

the display shows “L“ and “H“ in alternation. When the Touch Control 

is ON it can be switched- OFF at any time by operating the ON/OFF 

key. This is also valid if the control has been locked (activated child 

safety feature). 

The ON/OFF key has always priority in the switch-OFF function. 

Automatic switch-OFF 

When the control is ON it automatically switches-OFF after 

20 seconds if no cooking zone or select key has been operated 

within this period of time. If case of a cooking zone selection, the 

automatic switch-OFF time is composed of 10 seconds deselection 

time for a cooking zone at setting“0“ and 10 seconds switch-OFF 

time. 

Switching a cooking zone ON and OFF 

First place the pan in the chosen cooking zone. If the pan is not 

present the system cannot be switched on the correspondent zone. 

If the touch control is switched on, the cooking zone can be selected 

by pressing the button (4) of the corresponding zone. 

The display (5) of the zone selected lights up, while the remaining 

displays are dimmed. if the cooking zone is “hot”, “H” and “0” are 

alternately displayed. 

Press the PLUS (3) or MINUS (2) button to select a setting and the 

zone will begin to heat up. 

Once the cooking zone has been selected, the setting can be 

selected by keeping the PLUS (3) button pressed down. The setting 

begins at level 1 and increases by 1 level every 0.4 seconds. When 

setting “9” is reached, the setting will not be changed further. 

If the setting level has been selected using the MINUS (2) button, the 

start level is “9“ (maximum level). Keep the button pressed down to 

lower the active level by 1 every 0.4 seconds. When setting “0” is 

reached, there will be no further setting changed. The setting can 

only be changed by pressing the MINUS (2) or PLUS (3) button again. 

Switching a cooking zone off 

Select the zone to be switched off using the corresponding 

button (4). The display (5) of the zone selected lights up, while the 

remaining displays are dimmed. Press the Cooking zone (4) and 

MINUS (2) buttons at the same time and the setting level of the zone 

is changed to 0. Alternatively, the MINUS button (2) can be used to 

reduce the setting level to 0. 

If a cooking zone is “hot”, “H” and “0” will be alternately displayed. 

Switching-OFF all cooking zones 

Immediate switching-OFF of all cooking zones can be achieved 

anytime by means of the ON/OFF key. In the standby-mode an “H“ 

appears on all cooking zones which are “hot“. All other cooking zone 

displays are not illuminated. 

Wattage settings 

The output of the cooking zones can be set in 9 steps which 

are indicated by the figures “1“ thru “9“ by means of LED 

sevensegment-displays. 

In case more power is required, select the boost level (“P”)