background image

5

Copyright © 2009 Nokia. All rights reserved.

Get started

The headset contains the following 
parts shown on the title page: 
power key (1), volume key (2), 
answer/end key (3), earpiece (4), 
indicator light (5), charger 
connector (6), earloop (7), and 
microphone (8).

Before using the headset, you must 
charge the battery and pair the 
headset with a compatible device.

Parts of the device are magnetic. 
Metallic materials may be attracted to 
the device. Do not place credit cards or 
other magnetic storage media near the 
device, because information stored on 
them may be erased.

Charge the battery

Before charging the battery, 
carefully read “

Battery and charger 

information

”.

Warning:

 Use only 

chargers approved by 
Nokia for use with this 
particular model. The use of 
any other types may 
invalidate any approval or 
warranty, and may be 
dangerous.

When you disconnect the power cord 
of any accessory, grasp and pull the 
plug, not the cord.

1. Connect the charger to a wall 

outlet.

2. Connect the charger cable to the 

charger connector. The red 
indicator light is displayed 
during charging. Charging the 
battery fully may take up to 
1 hour and 15 minutes.

3. When the battery is fully 

charged, the green indicator 
light is displayed. Disconnect the 

Summary of Contents for 02719B5













Reviews: